MC908JL16CFJE Freescale Semiconductor, MC908JL16CFJE Datasheet - Page 192

• Manufacturer Part Number: MC908JL16CFJE
• Description: IC MCU 16K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JL16CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: DEMO908JL16E - BOARD DEMO FOR MC908JL16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Development Support
Upon power-on reset, if the received bytes of the security code do not match the data at locations
$FFF6–$FFFD, the host fails to bypass the security feature. The MCU remains in monitor mode, but
reading a FLASH location returns an invalid value and trying to execute code from FLASH causes an
illegal address reset. After receiving the eight security bytes from the host, the MCU transmits a break
character, signifying that it is ready to receive a command.
To determine whether the security code entered is correct, check to see if bit 6 of RAM address $60 is
set. If it is, then the correct security code has been entered and FLASH can be accessed.
If the security sequence fails, the device should be reset by a power-on reset and brought up in monitor
mode to attempt another entry. After failing the security sequence, the FLASH module can also be mass
erased by executing an erase routine that was downloaded into internal RAM. The mass erase operation
clears the security code locations so that all eight security bytes become $FF (blank).
16.3.9 ROM-Resident Routines
Eight routines stored in the monitor ROM area (thus ROM-resident) are provided for FLASH memory
manipulation. Six of the eight routines are intended to simplify FLASH program, erase, and load
operations. The other two routines are intended to simplify the use of the FLASH memory as EEPROM.
Table 16-10
192
shows a summary of the ROM-resident routines.
PTB0
V
RST
NOTES:
The MCU does not transmit a break character until after the host sends the
eight security bytes.
DD
1 = Echo delay, 2 bit times
2 = Data return delay, 2 bit times
4 = Wait 1 bit time before sending next byte.
FROM HOST
FROM MCU
Figure 16-14. Monitor Mode Entry Timing
4096 + 32 ICLK CYCLES
24 BUS CYCLES
MC68HC908JL16 Data Sheet, Rev. 1.1
1
NOTE
4
1
1
2
4
Freescale Semiconductor
1