AT91SAM9G45-CU Atmel, AT91SAM9G45-CU Datasheet
AT91SAM9G45-CU
Specifications of AT91SAM9G45-CU
Available stocks
Related parts for AT91SAM9G45-CU
AT91SAM9G45-CU Summary of contents
Page 1
... Errata on AT91SAM9G45 Engineering Sample 1. Scope This document describes the known errata found on Atmel’s AT91 ARM series AT91SAM9G45 device engineering samples with a date code prior to 0927. It applies to devices: • AT91SAM9G45 (with marking: CU-ES) 1.1 Marking All devices are marked with the Atmel logo and the order- ing code ...
Page 2
... The connection through USB to the SAM-BA monitor does not work. Problem Fix/Workaround Use JTAG or serial port to communicate with SAM-BA monitor. Note: 2.3.2 AT91SAM9G45-ES ROM Code Replacement Procedure to install AT91SAM9G45-ES ROM code replacement AT91SAM9G45_RomCode_Replacement.zip with USB issue fixed. Check and conform to the following Default Jumpers Settings. AT91SAM9G45 Errata 2 through USB See the steps described below ...
Page 3
... Alt-0128 #" 8. AT91SAM9G45-EKES returns ">" 9. close hyper terminal 10. close jumper JP12 (DataFlash 11. launch SAM-BA (Choose right COM port and AT91SAM9G45-EKES) 12. choose DataFlash media tab in the SAM-BA GUI interface 6485B–ATARM–28-Sep-09 AT91SAM9G45 Errata ® ...
Page 4
... DataFlash, choosing the Enable action in the Scripts rolling menu and press Execute 14. choose Send boot file, press Execute 15. select AT91SAM9G45_RomCode_Replacement.bin binary file and press Open; the media is written down 16. close SAM-BA On Reset, the faulty ROM code will copy the fixed ROM code in SRAM and launch it. The con- nexion through USB to the SAM-BA monitor will work ...
Page 5
... RX clock is divided clock (CKS = 0 and DIV different from 0) • RK pin set as output and provides the clock during data transfer (CKO = 2) • data sampled on RK falling edge (CKI = 0) The first clock cycle time generated by the RK pin is equal to MCK /(2 x (value +1)). 6485B–ATARM–28-Sep-09 AT91SAM9G45 Errata 5 ...
Page 6
... UDPHS and UHPHS shared UTMI transceiver The switch allowing to share a UTMI transceiver between the host port and the device port works only when switching from host to device. It does not work when switching from device to host. Problem Fix/Workaround None AT91SAM9G45 Errata 6 6485B–ATARM–28-Sep-09 ...
Page 7
... PDC Interruption ENDRX is received, reconfigure the USART in Mode T1 in US_MR prior to transmitting. 2.12.2 USART: Bad value in Number of Errors Register The Number of Errors Register (US_NER) always returns 0 instead of the ISO7816 error number. Problem/Fix Workaround None 6485B–ATARM–28-Sep-09 AT91SAM9G45 Errata 7 ...
Page 8
... Revision History Doc. Rev Comments Figure 2-1 “Default Jumpers Settings” on page 3 6485B “MMC boot” removed from 6485A First issue AT91SAM9G45 Errata 8 added. Section 2.3.3 on page 4. Change Request Ref. 6678 6643 6485B–ATARM–28-Sep-09 ...
Page 9
... AT91SAM9G45 Errata 9 ...
Page 10
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...