ATXMEGA256A3-MH Atmel, ATXMEGA256A3-MH Datasheet - Page 119
![MCU AVR 256K FLASH 1.8V 64-QFN](/photos/12/13/121326/313-64-qfn_sml.jpg)
ATXMEGA256A3-MH
Manufacturer Part Number
ATXMEGA256A3-MH
Description
MCU AVR 256K FLASH 1.8V 64-QFN
Manufacturer
Atmel
Series
AVR® XMEGAr
Datasheet
1.ATXMEGA64A3-MH.pdf
(134 pages)
Specifications of ATXMEGA256A3-MH
Core Processor
AVR
Core Size
8/16-Bit
Speed
32MHz
Connectivity
I²C, IrDA, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
50
Program Memory Size
256KB (128K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.6 V ~ 3.6 V
Data Converters
A/D 16x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-MLF®, 64-QFN
Processor Series
ATXMEGA256x
Core
AVR8
Data Bus Width
8 bit, 16 bit
Data Ram Size
16 KB
Interface Type
I2C, SPI, USART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
50
Number Of Timers
8
Operating Supply Voltage
1.6 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
8 bit, 2 Channel
On-chip Dac
2 bit, 1 Channel
Package
64QFN EP
Device Core
AVR
Family Name
XMEGA
Maximum Speed
32 MHz
For Use With
ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEM
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ATXMEGA256A3-MU
ATXMEGA256A3-MU
ATXMEGA256A3-MU
8068T–AVR–12/10
5. ADC Event on compare match non-functional
6. Bandgap measurement with the ADC is non-functional when VCC is below 2.7V
7. Accuracy lost on first three samples after switching input to ADC gain stage
8. Configuration of PGM and CWCM not as described in XMEGA A Manual
Table 36-4.
9. PWM is not restarted properly after a fault in cycle-by-cycle mode
10. BOD will be enabled after any reset
Problem fix/Workaround
Keep the amplified voltage output from the ADC gain stage below 2.4 V in order to get a cor-
rect result, or keep ADC voltage reference below 2.4 V.
ADC signalling event will be given at every conversion complete even if Interrupt mode (INT-
MODE) is set to BELOW or ABOVE.
Problem fix/Workaround
Enable and use interrupt on compare match when using the compare function.
The ADC can not be used to do bandgap measurements when VCC is below 2.7V.
Problem fix/Workaround
None.
Due to memory effect in the ADC gain stage, the first three samples after changing input
channel must be disregarded to achieve 12-bit accuracy.
Problem fix/Workaround
Run three ADC conversions and discard these results after changing input channels to ADC
gain stage.
Enabling Common Waveform Channel Mode will enable Pattern generation mode (PGM),
but not Common Waveform Channel Mode.
Enabling Pattern Generation Mode (PGM) and not Common Waveform Channel Mode
(CWCM) will enable both Pattern Generation Mode and Common Waveform Channel Mode.
Problem fix/Workaround
When the AWeX fault restore mode is set to cycle-by-cycle, the waveform output will not
return to normal operation at first update after fault condition is no longer present.
Problem fix/Workaround
Do a write to any AWeX I/O register to re-enable the output.
If any reset source goes active, the BOD will be enabled and keep the device in reset if the
VCC voltage is below the programmed BOD level. During Power-On Reset, reset will not be
released until VCC is above the programmed BOD level even if the BOD is disabled.
PGM
0
0
1
1
Configure PWM and CWCM according to this table:
CWCM
0
1
0
1
Description
PGM and CWCM disabled
PGM enabled
PGM and CWCM enabled
PGM enabled
XMEGA A3
119