PIC24HJ256GP610-I/PF Microchip Technology, PIC24HJ256GP610-I/PF Datasheet - Page 143

• Manufacturer Part Number: PIC24HJ256GP610-I/PF
• Description: IC PIC MCU FLASH 128KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ256GP610-I/PF

• Program Memory Type: FLASH
• Program Memory Size: 256KB (85.5K x 24)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b, 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: 3-Wire/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 13
• Operating Supply Voltage: 0 V to 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (32-ch x 12-bit)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.0
The Timer1 module is a 16-bit timer, which can serve
as the time counter for the real-time clock, or operate
as a free-running interval timer/counter. Timer1 can
operate in three modes:
• 16-bit Timer
• 16-bit Synchronous Counter
• 16-bit Asynchronous Counter
Timer1 also supports these features:
• Timer gate operation
• Selectable prescaler settings
• Timer operation during CPU Idle and Sleep
• Interrupt on 16-bit Period register match or falling
FIGURE 12-1:
© 2009 Microchip Technology Inc.
Note:
modes
edge of external gate signal
TIMER1
This data sheet summarizes the features
of the PIC24HJXXXGPX06/X08/X10 fam-
ily of devices. However, it is not intended
to be a comprehensive reference source.
To complement the information in this data
sheet, refer to the “PIC24H Family Refer-
ence Manual”, Section 11. “Timers”
(DS70244), which is available from the
Microchip website (www.microchip.com).
SOSCO/
SOSCI
Set T1IF
T1CK
16-BIT TIMER1 MODULE BLOCK DIAGRAM
TGATE
0
1
Reset
Equal
SOSCEN
PIC24HJXXXGPX06/X08/X10
Comparator
TMR1
PR1
Q
Q
Gate
Sync
CK
T
CY
D
Figure 12-1 presents a block diagram of the 16-bit
timer module.
To configure Timer1 for operation:
1.
2.
3.
4.
5.
6.
Set the TON bit (= 1) in the T1CON register.
Select the timer prescaler ratio using the
TCKPS<1:0> bits in the T1CON register.
Set the Clock and Gating modes using the TCS
and TGATE bits in the T1CON register.
Set or clear the TSYNC bit in T1CON to select
synchronous or asynchronous operation.
Load the timer period value into the PR1
register.
If interrupts are required, set the interrupt enable
bit, T1IE. Use the priority bits, T1IP<2:0>, to set
the interrupt priority.
TSYNC
1x
01
00
0
1
TON
TGATE
TCS
Sync
TCKPS<1:0>
1, 8, 64, 256
Prescaler
2
DS70175H-page 141