PIC16C76-20I/SP Microchip Technology, PIC16C76-20I/SP Datasheet - Page 95
![IC MCU OTP 8KX14 A/D PWM 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16C76-20I/SP
Manufacturer Part Number
PIC16C76-20I/SP
Description
IC MCU OTP 8KX14 A/D PWM 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C63A-04SP.pdf
(184 pages)
4.PIC16C72-04SO.pdf
(289 pages)
5.PIC16C76-04SP.pdf
(8 pages)
Specifications of PIC16C76-20I/SP
Core Size
8-Bit
Program Memory Size
14KB (8K x 14)
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Type
OTP
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Controller Family/series
PIC16C
No. Of I/o's
22
Ram Memory Size
368Byte
Cpu Speed
10MHz
No. Of Timers
3
Interface
I2C, SPI, USART
Embedded Interface Type
I2C, SPI, USART
Rohs Compliant
Yes
Package
28SPDIP
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
22
Interface Type
I2C/SPI/USART
On-chip Adc
5-chx8-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
13.6
During an interrupt, only the return PC value is saved
on the stack. Users may wish to save key registers dur-
ing an interrupt i.e., W register and STATUS register.
This will have to be implemented in software.
Example 13-1 stores and restores the STATUS, W, and
PCLATH registers. The register W_TEMP must be
defined in each bank and must be defined at the same
offset from the bank base address (i.e., if W_TEMP is
defined at 0x20 in bank 0, it must also be defined at
0xA0 in bank 1).
EXAMPLE 13-1:
13.7
The Watchdog Timer is a free running on-chip RC oscil-
lator, which does not require any external components.
This RC oscillator is separate from the RC oscillator of
the OSC1/CLKIN pin. The WDT will run, even if the
clock on the OSC1/CLKIN and OSC2/CLKOUT pins of
the device has been stopped, for example, by execu-
tion of a SLEEP instruction.
During normal operation, a WDT time-out generates a
device RESET (Watchdog Timer Reset). If the device is
in SLEEP mode, a WDT time-out causes the device to
wake-up and resume normal operation (Watchdog
Timer Wake-up).
The WDT can be permanently disabled by clearing
configuration bit WDTE (Section 13.1).
2000 Microchip Technology Inc.
MOVWF
SWAPF
CLRF
MOVWF
MOVF
MOVWF
:
(ISR)
:
MOVF
MOVWF
SWAPF
MOVWF
SWAPF
SWAPF
Context Saving During Interrupts
Watchdog Timer (WDT)
W_TEMP
STATUS,W
STATUS
STATUS_TEMP
PCLATH, W
PCLATH_TEMP
PCLATH_TEMP, W
PCLATH
STATUS_TEMP, W
STATUS
W_TEMP,F
W_TEMP,W
SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
;Copy W to TEMP register, could be bank one or zero
;Swap status to be saved into W
;bank 0, regardless of current bank, Clears IRP,RP1,RP0
;Save status to bank zero STATUS_TEMP register
;Only required if using pages 1, 2 and/or 3
;Save PCLATH into W
;Restore PCLATH
;Move W into PCLATH
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
;Swap W_TEMP into W
;User ISR code goes here
PIC16C63A/65B/73B/74B
The example:
a)
b)
c)
d)
e)
f)
13.7.1
The WDT has a nominal time-out period of 18 ms
(parameter #31, T
temperature, V
time-out periods are desired, a prescaler with a division
ratio of up to 1:128 can be assigned to the WDT under
software control, by writing to the OPTION register.
Time-out periods up to 128 T
The CLRWDT and SLEEP instructions clear the WDT
and the postscaler, if assigned to the WDT. In addition,
the SLEEP instruction prevents the WDT from generat-
ing a RESET, but will allow the WDT to wake the device
from SLEEP mode.
The TO bit in the STATUS register will be cleared upon
a WDT time-out.
Stores the W register.
Stores the STATUS register in bank 0.
Stores the PCLATH register.
Executes the ISR code.
Restores the STATUS register
(and bank select bit).
Restores the W and PCLATH registers.
WDT PERIOD
DD
WDT
, and process variations. If longer
). The time-out periods vary with
WDT
can be realized.
DS30605C-page 95