PIC16C76-20I/SP Microchip Technology, PIC16C76-20I/SP Datasheet - Page 23
![IC MCU OTP 8KX14 A/D PWM 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16C76-20I/SP
Manufacturer Part Number
PIC16C76-20I/SP
Description
IC MCU OTP 8KX14 A/D PWM 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C63A-04SP.pdf
(184 pages)
4.PIC16C72-04SO.pdf
(289 pages)
5.PIC16C76-04SP.pdf
(8 pages)
Specifications of PIC16C76-20I/SP
Core Size
8-Bit
Program Memory Size
14KB (8K x 14)
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Type
OTP
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Controller Family/series
PIC16C
No. Of I/o's
22
Ram Memory Size
368Byte
Cpu Speed
10MHz
No. Of Timers
3
Interface
I2C, SPI, USART
Embedded Interface Type
I2C, SPI, USART
Rohs Compliant
Yes
Package
28SPDIP
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
22
Interface Type
I2C/SPI/USART
On-chip Adc
5-chx8-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
4.2.2.5
This register contains the individual flag bits for the
peripheral interrupts.
REGISTER 4-5:
2000 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
PIR1 Register
PIR1 REGISTER (ADDRESS 0Ch)
PSPIF
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
ADIF
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (clear by reading RCREG)
0 = The USART receive buffer is empty
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (clear by writing to TXREG)
0 = The USART transmit buffer is full
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Note 1: PIC16C63A/73B devices do not have a parallel slave port implemented. This bit loca-
bit 7
Legend:
R = Readable bit
-n = Value at POR
PSPIF
R/W-0
(2)
2: PIC16C63A/65B devices do not have an A/D implemented. This bit location is
(1)
(1)
: A/D Converter Interrupt Flag bit
: Parallel Slave Port Read/Write Interrupt Flag bit
tion is reserved on these devices.
reserved on these devices.
ADIF
R/W-0
(2)
RCIF
R-0
W = Writable bit
’1’ = Bit is set
PIC16C63A/65B/73B/74B
TXIF
R-0
Note:
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit, or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt
SSPIF
R/W-0
.
CCP1IF
R/W-0
x = Bit is unknown
TMR2IF
R/W-0
DS30605C-page 23
TMR1IF
R/W-0
bit 0