AT89C5130A-PUTUM Atmel, AT89C5130A-PUTUM Datasheet - Page 48

• Manufacturer Part Number: AT89C5130A-PUTUM
• Description: IC 8051 MCU FLASH 16K USB 32QFN
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5130A-PUTUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Package: 32QFN EP
• Device Core: 8051
• Family Name: 89C
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: SPI/TWI/UART/USB
• Number Of Timers: 3
• Processor Series: AT89x
• Core: 8051
• Data Ram Size: 1.25 KB
• Maximum Clock Frequency: 48 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89STK-05
• Minimum Operating Temperature: - 40 C
• Height: 0.95 mm
• Length: 7 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: AT89C5130A-PUTIM; AT89C5130A-PUTIM

11.5
11.5.1
48
Hardware Conditions
AT89C5130A/31A-M
High Pin Count Hardware Conditions (PLCC52, QFP64)
It is possible to force the controller to execute the bootloader after a Reset with hardware condi-
tions. Depending on the product type (low pin count or high pin count package), there are two
methods to apply the hardware conditions.
For high pin count packages, the hardware conditons (EA = 1, PSEN = 0) are sampled during
the RESET rising edge to force the on-chip bootloader execution (See
172). In this way the bootloader can be carried out regardless of the user Flash memory content.
It is recommended to pull the PSEN pin down to ground though a 1K resistor to prevent the
PSEN pin from being damaged (see
Figure 11-3. ISP Hardware conditions
As PSEN is an output port in normal operating mode (running user application or bootloader
code) after reset, it is recommended to release PSEN after rising edge of reset signal.
To ensure correct microcontroller startup, the PSEN pin should not be tied to ground during
power-on (see
GND
Description
Copy of the Device ID#3: Name and Revision
1K
GND
VCC
Figure 11-4
/PSEN
RST
EA
Bootloader
below).
VCC
VSS
GND
VCC
XTAL2
XTAL1
ALE
Figure 11-3
Unconnected
C2
Crystal
C1
below).
GND
GND
Default Value
FFh
Figure 27-5 on page
4337K–USB–04/08
Address
61h