PIC24FJ96GA006-I/PT Microchip Technology, PIC24FJ96GA006-I/PT Datasheet - Page 121
![IC PIC MCU FLASH 48KX16 64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC24FJ96GA006-I/PT
Manufacturer Part Number
PIC24FJ96GA006-I/PT
Description
IC PIC MCU FLASH 48KX16 64TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.DV164033.pdf
(50 pages)
2.PIC24FJ16GA002-ISS.pdf
(52 pages)
3.PIC24FJ64GA006-IPT.pdf
(240 pages)
4.PIC24FJ64GA006-IPT.pdf
(22 pages)
Specifications of PIC24FJ96GA006-I/PT
Program Memory Type
FLASH
Program Memory Size
96KB (32K x 24)
Package / Case
64-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
16MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
53
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
53
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011, DV164033, AC164127, MA240011
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ96GA006-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
14.0
The Serial Peripheral Interface (SPI) module is a syn-
chronous serial interface useful for communicating with
other peripheral or microcontroller devices. These
peripheral devices may be serial EEPROMs, shift reg-
isters, display drivers, A/D Converters, etc. The SPI
module is compatible with Motorola’s SPI and SIOP
interfaces.
The module supports operation in two buffer modes. In
Standard mode, data is shifted through a single serial
buffer. In Enhanced Buffer mode, data is shifted
through an 8-level FIFO buffer.
The module also supports a basic framed SPI protocol
while operating in either Master or Slave modes. A total
of four framed SPI configurations are supported.
The SPI serial interface consists of four pins:
• SDIx: Serial Data Input
• SDOx: Serial Data Output
• SCKx: Shift Clock Input or Output
• SSx: Active-Low Slave Select or Frame
The SPI module can be configured to operate, using 2,
3 or 4 pins. In the 3-pin mode, SSx is not used. In the
2-pin mode, both SDOx and SSx are not used.
A block diagram of the module is shown in Figure 14-1
and Figure 14-2.
© 2009 Microchip Technology Inc.
Note:
Note:
Synchronization I/O Pulse
Note:
SERIAL PERIPHERAL
INTERFACE (SPI)
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. Refer to Section 23. “Serial
Peripheral Interface (SPI)” (DS39699) in
the PIC24F Family Reference Manual for
more information.
Do not perform read-modify-write opera-
tions (such as bit-oriented instructions) on
the SPIxBUF register, in either Standard
or Enhanced Buffer mode.
In this section, the SPI modules are
referred to together as SPIx or separately
as SPI1 and SPI2. Special Function Reg-
isters will follow a similar notation. For
example, SPIxCON refers to the control
register for the SPI1 or SPI2 module.
PIC24FJ128GA010 FAMILY
To set up the SPI module for the Standard Master mode
of operation:
1.
2.
3.
4.
5.
To set up the SPI module for the Standard Slave mode
of operation:
1.
2.
3.
4.
5.
6.
7.
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON
register with MSTEN (SPIxCON1<5>) = 1.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Write the data to be transmitted to the SPIxBUF
register. Transmission (and reception) will start
as soon as data is written to the SPIxBUF
register.
Clear the SPIxBUF register.
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1 and
SPIxCON2
(SPIxCON1<5>) = 0.
Clear the SMP bit.
If the CKE bit is set, then the SSEN bit
(SPIxCON1<7>) must be set to enable the SSx
pin.
Clear the SPIROV bit (SPIxSTAT<6>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Clear the SPIxIF bit in the respective IFSx
register.
Set the SPIxIE bit in the respective IECx
register.
Write the SPIxIP bits in the respective IPCx
register to set the interrupt priority.
Clear the SPIxIF bit in the respective IFSx
register.
Set the SPIxIE bit in the respective IECx
register.
Write the SPIxIP bits in the respective IPCx
register to set the interrupt priority.
registers
with
DS39747E-page 121
MSTEN