PIC24FJ64GA104-I/PT Microchip Technology, PIC24FJ64GA104-I/PT Datasheet - Page 16

• Manufacturer Part Number: PIC24FJ64GA104-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ64GA104-I/PT

• Core Size: 16-Bit
• Program Memory Size: 64KB (22K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC24
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, LIN, SPI, USART
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, LIN, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, IrDA, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM240001, MA240020, DM240002, DM240011, DV164033
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

DS51873B-page 16
FIGURE 2-1:
Once the driver installation finishes, it is necessary to determine the COM port number
that has been assigned. To do this in Windows, open Device Manager (from the control
panel, click on the System applet, select the Hardware tab, then click on Device
Manager). In the default view (Device by Connection), check under “Ports (COM &
LPT)” for the newly added COM port. The actual number of the new COM port will vary
depending on the hardware configuration of the system prior to driver installation.
2.1.3
With the board connected and the USB driver installed, the only remaining task is to
configure the terminal session. The required COM port settings are:
• Bits per Second: 1,000,000
• Data Bits: 8
• Parity: None
• Stop Bits: 1
• Flow Control: None.
At this point, the terminal is connected to the XLP board and communicating through
the emulated serial port. It may be necessary to press S1 (Master Clear) to reset to the
PIC24F microcontroller and obtain a display.
Note:
A to mini-B USB Cable
Configuring the Serial Terminal
If the serial terminal software being used does not support this baud rate, it will
be necessary to change the default baud rate for the firmware and reprogram
the board.
STARTER KIT SETUP
M
Development Board
 2010 Microchip Technology Inc.