PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 421

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

26.2
To set up the HLVD module:
1.
2.
3.
4.
5.
6.
26.3
When the module is enabled, the HLVD comparator
and voltage divider are enabled, and will consume
static current. The total current consumption, when
enabled,
parameter, D022B (I
acteristics: Power-Down and Supply Current
PIC18F47J53 Family (Industrial)”).
Depending on the application, the HLVD module does
not need to operate constantly. To decrease the current
requirements, the HLVD circuitry may only need to be
enabled for short periods where the voltage is checked.
After doing the check, the HLVD module may be
disabled.
 2010 Microchip Technology Inc.
Disable the module by clearing the HLVDEN bit
(HLVDCON<4>).
Write the value to the HLVDL<3:0> bits that
select the desired HLVD trip point.
Set the VDIRMAG bit to detect one of the
following:
• High voltage (VDIRMAG = 1)
• Low voltage (VDIRMAG = 0)
Enable the HLVD module by setting the
HLVDEN bit.
Clear the HLVD Interrupt Flag, HLVDIF
(PIR2<2>), which may have been set from a
previous interrupt.
If interrupts are desired, enable the HLVD inter-
rupt by setting the HLVDIE and GIE/GIEH bits
(PIE2<2> and INTCON<7>).
An interrupt will not be generated until the
IRVST bit is set.
HLVD Setup
Current Consumption
is
specified
HLVD
in
) (Section 31.2 “DC Char-
electrical
specification
Preliminary
PIC18F47J53 FAMILY
26.4
The internal reference voltage of the HLVD module,
specified in electrical specification parameter D420
(see Table 31-8 in Section 31.0 “Electrical Charac-
teristics”), may be used by other internal circuitry,
such as the Programmable Brown-out Reset (BOR).
If the HLVD or other circuits using the voltage reference
are disabled to lower the device’s current consumption,
the reference voltage circuit will require time to become
stable before a low or high-voltage condition can be
reliably detected. This start-up time, T
interval that is independent of device clock speed. It is
specified in electrical specification, parameter 36
(Table 31-14).
The HLVD interrupt flag is not enabled until T
expired and a stable reference voltage is reached. For
this reason, brief excursions beyond the set point may
not be detected during this interval. Refer to Figure 26-2
or Figure 26-3.
HLVD Start-up Time
DS39964B-page 421
IRVST
IRVST
, is an
has