DSPIC30F2010-20I/MM Microchip Technology, DSPIC30F2010-20I/MM Datasheet - Page 83

• Manufacturer Part Number: DSPIC30F2010-20I/MM
• Description: IC DSPIC MCU/DSP 12K 28QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2010-20I/MM

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 20
• Flash Memory Size: 12KB
• Supply Voltage Range: 2.5V To 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F2010-20I/MMG; DSPIC30F201020IMM; DSPIC30F201020IMM

14.0
This module simplifies the task of generating multiple,
synchronized Pulse Width Modulated (PWM) outputs.
In particular, the following power and motion control
applications are supported by the PWM module:
• Three-Phase AC Induction Motor
• Switched Reluctance (SR) Motor
• Brushless DC (BLDC) Motor
• Uninterruptible Power Supply (UPS)
The PWM module has the following features:
• Six PWM I/O pins with three duty cycle generators
• Up to 16-bit resolution
• ‘On-the-Fly’ PWM frequency changes
© 2008 Microchip Technology Inc.
Note:
MOTOR CONTROL PWM
MODULE
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals, register descriptions and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046).
• Edge and Center-Aligned Output modes
• Single Pulse Generation mode
• Interrupt support for asymmetrical updates in
• Output override control for Electrically
• ‘Special Event’ comparator for scheduling other
• FLTA pin to optionally drive each of the PWM
This module contains three duty cycle generators,
numbered 1 through 3. The module has six PWM
output pins, numbered PWM1H/PWM1L through
PWM3H/PWM3L. The six I/O pins are grouped into
high/low numbered pairs, denoted by the suffix H or L,
respectively. For complementary loads, the low PWM
pins are always the complement of the corresponding
high I/O pin.
A simplified block diagram of the Motor Control PWM
modules is shown in Figure 14-1.
The PWM module allows several modes of operation
which are beneficial for specific power control
applications.
Center-Aligned mode
Commutative Motor (ECM) operation
peripheral events
output pins to a defined state
dsPIC30F2010
DS70118H-page 83