PIC16F872-I/SO Microchip Technology, PIC16F872-I/SO Datasheet - Page 28

• Manufacturer Part Number: PIC16F872-I/SO
• Description: IC MCU FLASH 2KX14 EE 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F872-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Eeprom Size: 64 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C/SPI/SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL309-1073 - ADAPTER 28-SOIC TO 28-SOIC309-1024 - ADAPTER 28-SOIC TO 28-DIP309-1023 - ADAPTER 28-SOIC TO 28-DIP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F872
3.4
Reading FLASH Program memory is much like that of
EEPROM Data memory, only two NOP instructions
must be inserted after the RD bit is set. These two
instruction cycles that the NOP instructions execute will
be used by the microcontroller to read the data out of
program memory and insert the value into the
EEDATH:EEDATA registers. Data will be available fol-
lowing the second NOP instruction. EEDATH and
EEDATA will hold their value until another read opera-
tion is initiated, or until they are written by firmware.
EXAMPLE 3-3:
3.5
Writing to FLASH Program memory is unique in that the
microcontroller does not execute instructions while pro-
gramming is taking place. The oscillator continues to
run and all peripherals continue to operate and queue
interrupts, if enabled. Once the write operation com-
pletes (specification #D133), the processor begins exe-
cuting code from where it left off. The other important
difference when writing to FLASH Program memory is
that the WRT configuration bit, when clear, prevents
any writes to program memory (see Table 3-1).
Just like EEPROM Data memory, there are many steps
in writing to the FLASH Program memory. Both
address and data values must be written to the SFRs.
The EEPGD bit must be set and the WREN bit must be
set to enable writes. The WREN bit should be kept
DS30221C-page 26
Reading the FLASH Program
Memory
Writing to the FLASH Program
Memory
BSF
BCF
MOVF
MOVWF
MOVF
MOVWF
BSF
BSF
BSF
NOP
NOP
BCF
MOVF
MOVWF
MOVF
MOVWF
FLASH PROGRAM READ
EECON1, EEPGD
STATUS, RP1
STATUS, RP0
ADDRL, W
EEADR
ADDRH,W
EEADRH
STATUS, RP0
EECON1, RD
STATUS, RP0
EEDATA, W
DATAL
EEDATH,W
DATAH
;
;Bank 2
;Write the
;address bytes
;for the desired
;address to read
;Bank 3
;Point to Program memory
;Start read operation
;Required two NOPs
;
;Bank 2
;DATAL = EEDATA
;
;DATAH = EEDATH
;
The steps to reading the FLASH Program Memory are:
1.
2.
3.
4.
5.
clear at all times, except when writing to the FLASH
Program memory. The WR bit can only be set if the
WREN bit was set in a previous operation, i.e., they
both cannot be set in the same operation. The WREN
bit should then be cleared by firmware after the write.
Clearing the WREN bit before the write actually com-
pletes will not terminate the write in progress.
Writes to program memory must also be prefaced with
a special sequence of instructions that prevent inad-
vertent write operations. This is a sequence of five
instructions that must be executed without interruption
for each byte written. These instructions must then be
followed by two NOP instructions to allow the microcon-
troller to setup for the write operation. Once the write is
complete, the execution of instructions starts with the
instruction after the second NOP.
Write the address to EEADRH:EEADR. Make
sure that the address is not larger than the mem-
ory size of the device.
Set the EEPGD bit to point to FLASH Program
memory.
Set the RD bit to start the read operation.
Execute two NOP instructions to allow the micro-
controller to read out of program memory.
Read the data from the EEDATH:EEDATA
registers.
© 2006 Microchip Technology Inc.