PIC18F24J11-I/SO Microchip Technology, PIC18F24J11-I/SO Datasheet - Page 105

• Manufacturer Part Number: PIC18F24J11-I/SO
• Description: IC PIC MCU FLASH 16K 2V 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F24J11-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DM183033, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MILAC164332 - MODULE SKT FOR 28SOIC 18F45J10
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6.5.2
The PIC18F46J11 family of devices has a feature that
allows programming a single word (two bytes). This
feature is enabled when the WPROG bit is set. If the
memory location is already erased, the following
sequence is required to enable this feature:
1.
2.
EXAMPLE 6-4:
© 2009 Microchip Technology Inc.
PROGRAM_MEMORY
Load the Table Pointer register with the address
of the data to be written. (It must be an even
address.)
Write the 2 bytes into the holding registers by
performing table writes. (Do not post-increment
on the second table write.)
Required
Sequence
FLASH PROGRAM MEMORY WRITE
SEQUENCE (WORD PRORAMMING).
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
TBLWT*+
MOVLW
MOVWF
TBLWT*
BSF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
BCF
BCF
SINGLE-WORD WRITE TO FLASH PROGRAM MEMORY
CODE_ADDR_UPPER
TBLPTRU
CODE_ADDR_HIGH
TBLPTRH
CODE_ADDR_LOW
TBLPTRL
DATA0
TABLAT
DATA1
TABLAT
EECON1, WPROG
EECON1, WREN
INTCON, GIE
55h
EECON2
0AAh
EECON2
EECON1, WR
INTCON, GIE
EECON1, WPROG
EECON1, WREN
; Load TBLPTR with the base address
; The table pointer must be loaded with an even
; LSB of word to be written
; MSB of word to be written
; The last table write must not increment the table
; enable single word write
; enable write to memory
; disable interrupts
; write 55h
; write AAh
; start program (CPU stall)
; re-enable interrupts
; disable single word write
; disable write to memory
address
pointer! The table pointer needs to point to the
MSB before starting the write operation.
PIC18F46J11 FAMILY
3.
4.
5.
6.
7.
8.
9.
Set the WREN bit (EECON1<2>) to enable
writes and the WPROG bit (EECON1<5>) to
select Word Write mode.
Disable interrupts.
Write 55h to EECON2.
Write 0AAh to EECON2.
Set the WR bit; this will begin the write cycle.
The CPU will stall for the duration of the write for
T
Re-enable interrupts.
IW
(see parameter D133A).
DS39932C-page 105