ATTINY88-AU Atmel, ATTINY88-AU Datasheet - Page 141

• Manufacturer Part Number: ATTINY88-AU
• Description: MCU AVR 8K ISP FLASH 1.8V 32TQFP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY88-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 28
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire/I2S/SPI
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATQT600, ATAVRTS2080B
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.8.1
8008G–AVR–04/11
Master Transmitter Mode
The following sections describe each of these modes. Possible status codes are described
along with figures detailing data transmission in each of the modes. These figures contain the
following abbreviations:
In
numbers in the circles show the status code held in TWSR, with the prescaler bits masked to
zero. At these points, actions must be taken by the application to continue or complete the TWI
transfer. The TWI transfer is suspended until the TWINT Flag is cleared by software.
When the TWINT Flag is set, the status code in TWSR is used to determine the appropriate soft-
ware action. For each status code, the required software action and details of the following serial
transfer are given in
these tables.
In the Master Transmitter mode, a number of data bytes are transmitted to a Slave Receiver
(see
The format of the following address packet determines whether Master Transmitter or Master
Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is trans-
mitted, MR mode is entered. All the status codes mentioned in this section assume that the
prescaler bits are zero or are masked to zero.
Figure 15-11. Data Transfer in Master Transmitter Mode
SDA
SCL
Figure 15-12
S: START condition
Rs: REPEATED START condition
R: Read bit (high level at SDA)
W: Write bit (low level at SDA)
A: Acknowledge bit (low level at SDA)
A: Not acknowledge bit (high level at SDA)
Data: 8-bit data byte
P: STOP condition
SLA: Slave Address
Figure
15-11). In order to enter a Master mode, a START condition must be transmitted.
TRANSMITTER
Device 1
to
MASTER
Figure
Table 15-2
15-18, circles are used to indicate that the TWINT Flag is set. The
Device 2
RECEIVER
SLAVE
to
Table
15-5. Note that the prescaler bits are masked to zero in
Device 3
........
Device n
V
CC
ATtiny48/88
R1
R2
141