ATTINY261-20MU Atmel, ATTINY261-20MU Datasheet - Page 39

• Manufacturer Part Number: ATTINY261-20MU
• Description: IC MCU AVR 2K FLASH 20MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261-20MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: 2-Wire, SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 32MLF EP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7.4
7.4.1
7.4.2
2588E–AVR–08/10
Register Description
MCUCR – MCU Control Register
PRR – Power Reduction Register
Refer to
able Register 1” on page 162
The MCU Control Register contains control bits for power management.
• Bit 5 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
• Bits 4, 3 – SM1:0: Sleep Mode Select Bits 2:0
These bits select between the three available sleep modes as shown in
Table 7-2.
• Bit 2 – Res: Reserved Bit
This bit is reserved and will always read zero.
The Power Reduction Register provides a method to reduce power consumption by allowing
peripheral clock signals to be disabled.
• Bits 7, 6, 5, 4 – Res: Reserved Bits
These bits are reserved and will always read zero.
• Bit 3 – PRTIM1: Power Reduction Timer/Counter1
Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1
is enabled, operation will continue like before the shutdown.
Bit
0x35 (0x55)
Read/Write
Initial Value
Bit
0x36 (0x56)
Read/Write
Initial Value
SM1
0
0
1
1
“DIDR0 – Digital Input Disable Register 0” on page 162
7
–
R
0
Sleep Mode Select
7
–
R
0
6
PUD
R/W
0
6
-
R
0
SM0
0
1
0
1
for details.
5
SE
R/W
0
5
-
R
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Standby
4
SM1
R/W
0
4
-
R
0
3
SM0
R/W
0
3
PRTIM1
R/W
0
2
—
R
0
2
PRTIM0
R/W
0
or
“DIDR1 – Digital Input Dis-
1
ISC01
R/W
0
1
PRUSI
R/W
0
Table
0
ISC00
R/W
0
7-2.
0
PRADC
R/W
0
MCUCR
PRR
39