ATTINY24V-10MU Atmel, ATTINY24V-10MU Datasheet - Page 170

• Manufacturer Part Number: ATTINY24V-10MU
• Description: IC MCU AVR 2K FLASH 10MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24V-10MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 10MHz
• Interface Type: SPI/USI
• Total Internal Ram Size: 128Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: MLF
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.7.5
170
ATtiny24/44/84
Programming the EEPROM
Figure 19-4. Addressing the Flash which is Organized in Pages
Figure 19-5. High-voltage Serial Programming Waveforms
The EEPROM is organized in pages, see
EEPROM, the data is latched into a page buffer. This allows one page of data to be pro-
grammed simultaneously. The programming algorithm for the EEPROM Data memory is as
follows (refer to
SDO
PB0
PB1
PB2
PB3
1. Load Command “Write EEPROM”.
2. Load EEPROM Page Buffer.
3. Program EEPROM Page. Wait after Instr. 2 until SDO goes high for the “Page Program-
4. Repeat 2 through 3 until the entire EEPROM is programmed or until all data has been
5. End Page Programming by Loading Command “No Operation”.
SDI
SCI
SII
ming” cycle to finish.
programmed.
PROGRAM MEMORY
PROGRAM
COUNTER
PAGE
0
MSB
Table 19-16 on page
PAGE ADDRESS
WITHIN THE FLASH
MSB
MSB
1
PCMSB
2
PCPAGE
3
171):
4
PAGEMSB
PCWORD
Table 20-12 on page
5
WORD ADDRESS
WITHIN A PAGE
6
INSTRUCTION WORD
7
PAGE
LSB
LSB
LSB
8
183. When programming the
9
PCWORD[PAGEMSB:0]:
00
01
02
PAGEEND
10
8006K–AVR–10/10