Z8F08200100KITG Zilog, Z8F08200100KITG Datasheet - Page 155
Z8F08200100KITG
Manufacturer Part Number
Z8F08200100KITG
Description
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer
Zilog
Series
Z8 Encore!®r
Type
MCUr
Datasheets
1.Z8F08200100KITG.pdf
(18 pages)
2.Z8F08200100KIT.pdf
(264 pages)
3.Z8F08200100KITG.pdf
(9 pages)
Specifications of Z8F08200100KITG
Contents
Evaluation Board, Cable, Power Supply, Software and Documentation
Silicon Manufacturer
Zilog
Core Architecture
Z8 Encore
Silicon Core Number
Z8F0822SJ020
Silicon Family Name
XP F0822
Rohs Compliant
Yes
For Use With/related Products
Z8 Encore!™
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4630
- Current page: 155 of 264
- Download datasheet (6Mb)
PS022517-0508
set, this bit is reset by the I
the IEN bit. If this bit is 1, it cannot be cleared to 0 by writing to the register.
BIRQ—Baud Rate Generator Interrupt Request
This bit allows the I
Controller is disabled. This bit is ignored when the I
1 = An interrupt occurs every time the BRG counts down to one.
0 = No BRG interrupt occurs.
TXI—Enable TDRE interrupts
This bit enables the transmit interrupt when the I
1 = Transmit Interrupt (and DMA transmit request) is enabled.
0 = Transmit Interrupt (and DMA transmit request) is disabled.
NAK—Send NAK
This bit sends a Not Acknowledge condition after the next byte of data is read from the
I
deasserted. If this bit is 1, it cannot be cleared to 0 by writing to the register.
FLUSH—Flush Data
Setting this bit to 1 clears the I
flushing of the I
data has been sent to the I
FILTEN—I
This bit enables low-pass digital filters on the SDA and SCL input signals. These filters
reject any input pulse with periods less than a full system clock cycle. The filters introduce
a 3-system clock cycle latency on the inputs.
1 = low-pass filters are enabled.
0 = low-pass filters are disabled.
2
C Slave. Once asserted, it is deasserted after a Not Acknowledge is sent or the IEN bit is
2
C Signal Filter Enable
2
C Data Register when a Not Acknowledge interrupt is received after the
2
C Controller to be used as an additional timer when the I
2
2
C Data Register. Reading this bit always returns 0.
C Controller after a STOP condition is sent or by deasserting
2
C Data Register and sets the TDRE bit to 1. This bit allows
2
C Data Register is empty (TDRE = 1).
2
C Controller is enabled.
Z8 Encore! XP
Product Specification
®
F0822 Series
I2C Controller
2
C
142
Related parts for Z8F08200100KITG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: