LTM4604AEV#PBF Linear Technology, LTM4604AEV#PBF Datasheet - Page 9

• Manufacturer Part Number: LTM4604AEV#PBF
• Description: IC UMODULE DC/DC LV 4A 66-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4604AEV#PBF

• Design Resources: LTM4604A Spice Model
• Output: 0.8 ~ 5 V
• Number Of Outputs: 1
• Power (watts): 20W
• Mounting Type: Surface Mount
• Voltage - Input: 2.38 ~ 5.5 V
• Package / Case: 66-LGA
• 1st Output: 0.8 ~ 5 VDC @ 4A
• Size / Dimension: 0.59" L x 0.35" W x 0.09" H (15mm x 9mm x 2.3mm)
• Power (watts) - Rated: 20W
• Operating Temperature: -40°C ~ 125°C
• Efficiency: 95%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

A typical LTM4604A application circuit is shown in
Figure 15. External component selection is primarily
determined by the maximum load current and output
voltage. Refer to Table 4 for specifi c external capacitor
requirements for a particular application.
V
There are restrictions in the maximum V
down ratio that can be achieved for a given input voltage.
The LTM4604A is 100% duty cycle, but the V
minimum dropout is a function of the load current. A typi-
cal 0.5V minimum is suffi cient (see Typical Performance
Characteristics).
Output Voltage Programming
The PWM controller has an internal 0.8V reference volt-
age. As shown in the Block Diagram, a 4.99k 0.5% internal
feedback resistor connects the V
The output voltage will default to 0.8V with no feedback
resistor. Adding a resistor R
programs the output voltage:
Table 1. FB Resistor vs Output Voltage
Input Capacitors
The LTM4604A module should be connected to a low ac-
impedance DC source. Two 10μF ceramic capacitors are
included inside the module. Additional input capacitors
are only needed if a large load step is required up to a
full 4A level. An input 47μF bulk capacitor is only needed
if the input source impedance is compromised by long
inductive leads or traces.
For a buck converter, the switching duty cycle can be
estimated as:
APPLICATIONS INFORMATION
IN
V
R
D
V
OUT
to V
FB
OUT
=
V
OUT
V
OUT
=
IN
Open
0.8V
0 8
Step-Down Ratios
.
V
•
4 99
1.2V
10k
.
R
k R
FB
+
5.76k
1.5V
FB
FB
OUT
from the FB pin to GND
4.02k
1.8V
and FB pins together.
IN
and V
2.37k
2.5V
IN
OUT
to V
1.62k
3.3V
step-
OUT
Without considering the inductor current ripple, the RMS
current of the input capacitor can be estimated as:
In the above equation, η% is the estimated effi ciency of
the power module. The bulk capacitor can be a switcher-
rated electrolytic aluminum capacitor, OS-CON capacitor
for bulk input capacitance due to high inductance traces
or leads. If a low inductance plane is used to power the
device, then no input capacitance is required. The two
internal 10μF ceramics are typically rated for 2A to 3A of
RMS ripple current. The worst-case ripple current for the
4A maximum current is 2A or less.
Output Capacitors
The LTM4604A is designed for low output voltage ripple.
The bulk output capacitors defi ned as C
with low enough effective series resistance (ESR) to meet
the output voltage ripple and transient requirements. C
can be a low ESR tantalum capacitor, a low ESR polymer
capacitor or an X5R/X7R ceramic capacitor. The typical
output capacitance range is 22μF to 100μF. Additional
output fi ltering may be required by the system designer
if further reduction of output ripple or dynamic transient
spike is required. Table 4 shows a matrix of different
output voltages and output capacitors to minimize the
voltage droop and overshoot during a 2A/μs transient.
The table optimizes the total equivalent ESR and total bulk
capacitance to maximize transient performance. The Linear
Technology μModule Power Design Tool can be provided
for further optimization.
Fault Conditions: Current Limit and Overcurrent
Foldback
The LTM4604A has current mode control, which inher-
ently limits the cycle-by-cycle inductor current not only
in steady-state operation, but also in transient.
To further limit current in the event of an overload condi-
tion, the LTM4604A provides foldback current limiting as
the output voltage falls. The LTM4604A device has over-
temperature shutdown protection that inhibits switching
operation around 150°C.
I
CIN(RMS)
=
I
OUT(MAX)
η%
• D • 1– D
(
LTM4604A
)
OUT
are chosen
4604af
9
OUT