HIP6004BCBZ Intersil, HIP6004BCBZ Datasheet
HIP6004BCBZ
Specifications of HIP6004BCBZ
Related parts for HIP6004BCBZ
HIP6004BCBZ Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 All other trademarks mentioned are the property of their respective owners. HIP6004B FN4567 2.05V DC DS(ON) | Intersil (and design registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved ...
Page 2
Pinouts HIP6004B (SOIC, TSSOP) TOP VIEW SEN OCSET VID0 4 17 VID1 5 16 VID2 6 15 VID3 14 7 VID4 8 13 COMP Typical Application PGOOD ...
Page 3
Block Diagram V SEN OCSET REFERENCE VID0 TTL D/A VID1 CONVERTER VID2 VID3 (DAC) VID4 FB COMP RT 3 HIP6004B POWER-ON 110% RESET (POR 90 OVER- 115% VOLTAGE + - + - OVER- CURRENT 200µA 4V ...
Page 4
Absolute Maximum Ratings Supply Voltage .+15V CC ...
Page 5
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted (Continued) PARAMETER POWER GOOD Upper Threshold (V /DACOUT) SEN Lower Threshold (V /DACOUT) SEN Hysteresis (V /DACOUT) SEN PGOOD Voltage Low Typical Performance Curves 1000 R PULLUP T TO +12V 100 10 ...
Page 6
GND (Pin 11) Signal ground for the IC. All voltage levels are measured with respect to this pin. PGOOD (Pin 12) PGOOD is an open collector output used to indicate the status of the converter output voltage. This pin is ...
Page 7
Over-Current Protection The over-current function protects the converter from a shorted output by using the upper MOSFET’s on-resistance monitor the current. This method enhances the DS(ON) converter’s efficiency and reduces cost by eliminating a current sensing resistor. 4V ...
Page 8
PIN NAME VID4 VID3 VID2 VID1 VID0 ...
Page 9
DRIVER OSC PWM COMPARATOR - DRIVER + ∆V OSC E REFERENCE ERROR AMP DETAILED COMPENSATION COMPONENTS COMP HIP6004B DACOUT FIGURE 7. VOLTAGE-MODE BUCK ...
Page 10
Modern microprocessors produce transient load rates above 1A/ns. High frequency capacitors initially supply the transient and slow the current load rate seen by the bulk capacitors. The bulk filter capacitor values are generally determined by the ESR (Effective Series Resistance) ...
Page 11
Only the upper MOSFET has switching losses, since the Schottky rectifier clamps the switching node before the synchronous rectifier turns on. These equations assume linear voltage-current transitions and do not adequately model power loss due the reverse-recovery of the ...
Page 12
... Core: Micrometals T50-52B; Each Winding: 10 Turns of 16AWG Core: Micrometals T50-52; Winding: 5 Turns of 18AWG 1N4148 or Equivalent 3A, 40V Schottky, Motorola MBR340 or Equivalent Intersil MOSFET; RFP70N03 HIP6004B in Application Note AN9672. Although the Application Note details the HIP6004, the same evaluation platform can be used to evaluate the HIP6004B. 2N6394 C IN +12V 2K ...
Page 13
Small Outline Plastic Packages (SOIC) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α µ 0.10(0.004) 0.25(0.010 NOTES: 1. Symbols are defined in ...
Page 14
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...