CS5467-ISZ Cirrus Logic Inc, CS5467-ISZ Datasheet - Page 32

• Manufacturer Part Number: CS5467-ISZ
• Description: IC ENERGY METERING 1PHASE 28SSOP
• Manufacturer: Cirrus Logic Inc

Specifications of CS5467-ISZ

• Package / Case: 28-SSOP
• Input Impedance: 30 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 0.8V
• Voltage - I/o Low: 0.2V
• Current - Supply: 3.5mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Meter Type: Single Phase
• Output Voltage Range: 2.4 V to 2.6 V
• Input Voltage Range: 2.4 V to 2.6 V
• Input Current: 100 nA
• Power Dissipation: 500 mW
• Operating Temperature Range: - 40 C to + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1555 - BOARD EVAL FOR CS5467 ADC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1197-5

8.2.12 Internal Status (Status) and Interrupt Mask (Mask)
32
DRDY
E2OR
TUP
23
15
Address: 15 ( Status ); 26 ( Mask )
Default =
The Status register indicates a variety of conditions within the chip. Writing a '1' to a Status register bit will
clear that bit if the condition that set it has been removed. Writing a '0' to any bit has no effect.
The Mask register is used to control the activation of the INT pin. Writing a '1' to a Mask register bit will allow
the corresponding Status register bit to activate the INT pin when set.
DRDY
V1OR (V2OR)
CRDY
I1ROR (I2ROR)
V1ROR (V2ROR) RMS Voltage Out of Range. Set when RMS voltage would cause the V1
E1OR (E2OR)
I1FAULT (I2FAULT)Indicates when a current fault condition has occurred.
V1SAG (V2SAG) Indicates when a voltage sag condition has occurred.
TUP
V1OD (V2OD)
I1OD (I2OD)
LSD
FUP
IC
7
I1OR (I2OR)
I1ROR
V2OD
I2OR
22
14
1 ( Status ), 0 ( Mask )
6
Data Ready. During conversion, this bit indicates that low-rate results have been updated.
It indicates completion of other commands and the reset sequence.
Current Out of Range. Set when the measured current would cause the I1 ( I2 ) register to
overflow.
Voltage Out of Range. Set when the measured voltage would cause the V1 ( V2 ) register
to overflow.
Conversion Ready. Indicates that sample rate (output word rate) results have been updat-
ed.
RMS Current Out of Range. Set when RMS current would cause the I1
ter to overflow.
ister to overflow.
Energy Out of Range. Set when average power would cause P1
Indicates when the Temperature register ( T ) has been updated.
Modulator oscillation has been detected in the voltage1 (voltage2) A/D.
Modulator oscillation has been detected in the current1 (current2) A/D.
Low Supply Detect. Set when the voltage on the PFMON pin falls below the specified low
level. The LSD bit cannot be reset until the voltage rises above the specified high level.
Frequency Updated. Indicates the Epsilon register has been updated.
Invalid Command. Normally logic 1. Set to 0 when an invalid command is received. It may
also indicate loss of serial command synchronization and the part may need to be re-ini-
tialized.
V1ROR
V2OR
I2OD
21
13
5
CRDY
E1OR
V1OD
20
12
4
I1FAULT
I2ROR
I1OD
19
11
3
V2ROR
V1SAG
LSD
18
10
2
I2FAULT
AVG
I1OR
FUP
17
9
1
( P2
RMS
RMS
AVG
( I2
CS5467
( V2
) to overflow.
RMS
V2SAG
V1OR
DS714F1
RMS
16
IC
8
0
) regis-
) reg-