XBP24-BPIT-004 Digi International, XBP24-BPIT-004 Datasheet - Page 90
XBP24-BPIT-004
Manufacturer Part Number
XBP24-BPIT-004
Description
Zigbee / 802.15.4 Modules XBee-PRO Znet 2.5 PCB Antenna
Manufacturer
Digi International
Datasheet
1.XB24-BPIT-004.pdf
(91 pages)
Specifications of XBP24-BPIT-004
Rohs
yes
Frequency Band
2.4 GHz
Line Of Sight Range
100 m
Data Rate
250 Kbps
Sensitivity
- 102 dBm
Operating Supply Voltage
3 V to 3.4 V
Output Power
63 mW
Antenna Connector Type
PCB
Maximum Operating Temperature
+ 85 C
- Current page: 90 of 91
- Download datasheet (2Mb)
ZigBee Command Set
API / AT Firmware Versions
Appendix C: Migrating from the 802.15.4
Modified Commands
New Commands
802.15.4 application:
Also, refer to the “Getting Started” section for more information.
The 802.15.4 firmware supports the AP command for setting the module into No API (AP=0), API
without escaping (AP=1), or API with escaping (AP=2) modes. The first digit in the 802.15.4
firmware versions is a '1'.
The ZigBee firmware comes in different versions to support the API interface (AP 1, 2 modes) or
the AT command set (AP 0 mode). The first digit in the ZigBee firmware versions is an '8'.
The following is a list of firmware versions:
This following are some of the differences in the ZigBee firmware assuming familiarity with the
© 2008 Digi International, Inc.
• ZigBee Command Set
• Address Assignment
• API / AT Firmware Versions
• CH - Read Only command that displays the operating channel that was selected from SC.
• MY - Read Only command that displays the assigned 16-bit network address of the device.
• AI - ZigBee definitions added to this command. See documentation.
• A1, A2 and CE commands are not supported.
• NJ (Node Join Time) - This value determines how long a Coordinator or Router will allow other
• MP (16-bit Parent Network Address). This value represents the 16-bit parent network address
• BH (Broadcast Hops). This value sets the maximum number of hops for each broadcast data
• 1.0xx - Coordinator, AT Command support (Transparent Mode)
• 1.1xx - Coordinator, API support (AP 1, 2)
• 1.2xx - Router, End Device, AT Command support (Transparent Mode)
• 1.3xx - Router, End Device, API support (AP 1, 2)
devices to join to it. This command is supported on Coordinators & Routers only.
of the module.
transmission. Setting this to 0 will use the maximum number of hops.
Protocol
89
Related parts for XBP24-BPIT-004
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MODULE 802.15.4 100MW CHIP ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 RS-232 ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE XBEE PRO ZNET 2.5 W/RPSMA
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
KIT STARTER XBEE PRO
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 100MW WIRE ANT
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE 802.15.4 100MW U.FL CON
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE XBEE PRO ZNET 2.5 W/CHIP
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE XBEE PRO ZNET 2.5 W/WHIP
Manufacturer:
Digi International/Maxstream
Datasheet:
Part Number:
Description:
MODULE ZIGBEE-PRO W/WIRED ANT
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE ZIGBEE-PRO W/RPSMA ANT
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
IC ARM MICROPROCESSOR 177BGA
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
DIGI CONNECT 4MB FLASH 8MB RAM
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 9P 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International/Maxstream
Datasheet: