K4H280438F SAMSUNG [Samsung semiconductor], K4H280438F Datasheet - Page 10

• Manufacturer Part Number: K4H280438F
• Description: 128Mb F-die DDR SDRAM Specification
• Manufacturer: SAMSUNG [Samsung semiconductor]

DDR SDRAM 128Mb F-die (x4, x8)
DDR SDRAM Spec Items & Test Conditions
Input/Output Capacitance
Note :
Operating current - One bank Active-Precharge;
tRC=tRCmin; tCK=7.5ns for DDR266, 6ns for DDR333;
DQ,DM and DQS inputs changing once per clock cycle;
address and control inputs changing once every two clock cycles.
Operating current - One bank operation ; One bank open, BL=4, Reads
- Refer to the following page for detailed test condition
Percharge power-down standby current; All banks idle; power - down mode;
CKE = <VIL(max); tCK=7.5ns for DDR266, 6ns for DDR333; Vin = Vref for DQ,DQS and DM.
Precharge Floating standby current; CS# > =VIH(min);All banks idle; CKE > = VIH(min); tCK=7.5ns for DDR266,
6ns for DDR333; Address and other control inputs changing once per clock cycle;
Vin = Vref for DQ,DQS and DM
Precharge Quiet standby current; CS# > = VIH(min); All banks idle;
CKE > = VIH(min); tCK=7.5ns for DDR266, 6ns for DDR333; Address and other control inputs stable at >=
VIH(min) or =<VIL(max); Vin = Vref for DQ ,DQS and DM
Active power - down standby current ; one bank active; power-down mode;
CKE=< VIL (max); tCK=7.5ns for DDR266, 6ns for DDR333; Vin = Vref for DQ,DQS and DM
Active standby current; CS# >= VIH(min); CKE>=VIH(min);
one bank active; active - precharge; tRC=tRASmax; tCK=7.5ns for DDR266, 6ns for DDR333;
DQ, DQS and DM inputs changing twice per clock cycle; address and other control inputs changing once per clock
cycle
Operating current - burst read; Burst length = 2; reads; continguous burst; One bank active; address and control
inputs changing once per clock cycle; CL=2 at 7.5ns for DDR266(A2), CL=2.5 at 7.5ns for DDR266(B0), 6ns for
DDR333; 50% of data changing on every transfer; lout = 0 m A
Operating current - burst write; Burst length = 2; writes; continuous burst;
One bank active address and control inputs changing once per clock cycle; CL=2 at tCK=7.5ns for DDR266(A2),
CL=2.5 at tCK=7.5ns for DDR266(B0), 6ns for DDR333; DQ, DM and DQS inputs changing twice per clock cycle,
50% of input data changing at every burst
Auto refresh current; tRC = tRFC(min) - 10*tCK for DDR266 at tCK=7.5ns; 12*tCK for DDR333 at tCK=6ns; dis-
tributed refresh
Self refresh current; CKE =< 0.2V; External clock on; tCK = 7.5ns for DDR266, 6ns for DDR333.
Orerating current - Four bank operation ; Four bank interleaving with BL=4
-Refer to the following page for detailed test condition
Input capacitance
(A0 ~ A11, BA0 ~ BA1, CKE, CS, RAS,CAS, WE)
Input capacitance( CK, CK )
Data & DQS input/output capacitance
Input capacitance(DM for x4/8, UDM/LDM for x16)
1.These values are guaranteed by design and are tested on a sample basis only.
2. Although DM is an input -only pin, the input capacitance of this pin must model the input capacitance of the DQ and DQS pins.
3. Unused pins are tied to ground.
4. This parameteer is sampled. VDDQ = +2.5V +0.2V, VDD = +3.3V +0.3V or +2.5V+0.2V, f=100MHz, tA=25°C, Vout(dc) =
(to facilitate trace matching at the board level).
This is required to match signal propagation times of DQ, DQS, and DM in the system.
VDDQ/2, Vout(peak to peak) = 0.2V. DM inputs are grouped with I/O pins - reflecting the fact that they are matched in loading
Parameter
Conditions
Symbol
COUT
CIN1
CIN2
CIN3
Min
2
2
4
4
(V
Max
3
3
5
5
DD
=2.5, V
DDQ
Rev. 1.1 May. 2004
Delta
0.25
0.5
0.5
=2.5V, T
DDR SDRAM
A
= 25°C, f=1MHz)
Unit
pF
pF
pF
pF
Symbol
IDD4W
IDD2Q
IDD3N
IDD4R
IDD7A
IDD2P
IDD2F
IDD3P
IDD0
IDD1
IDD5
IDD6
1,2,3,4
1,2,3,4
Note
4
4