PSD913F1-B-90JI ST Microelectronics, PSD913F1-B-90JI Datasheet - Page 63
PSD913F1-B-90JI
Manufacturer Part Number
PSD913F1-B-90JI
Description
Flash In-System Programmable ISP Peripherals For 8-bit MCUs
Manufacturer
ST Microelectronics
Datasheet
1.PSD913F1-B-90JI.pdf
(94 pages)
- Current page: 63 of 94
- Download datasheet (477Kb)
Preliminary Information
The
PSD9XX
Functional
Blocks
(cont.)
9.5.3 Reset and Power On Requirement
9.5.3.1 Power On Reset
Upon power up the PSD9XX requires a reset pulse of tNLNH-PO (minimum 1 ms) after
V
some of the registers and sets the Flash into operating mode. After the rising edge of
reset, the PSD9XX remains in the reset state for an additional tOPR (maximum 120 ns)
nanoseconds before the first memory access is allowed.
The PSD9XX Flash memory is reset to the read array mode upon power up. The FSi
and CSBOOTi select signals along with the write strobe signal must be in the false
state during power-up reset for maximum security of the data contents and to remove
the possibility of a byte being written on the first edge of a write strobe signal. Any Flash
memory write cycle initiation is prevented automatically when V
9.5.3.2 Warm Reset
Once the device is up and running, the device can be reset with a much shorter pulse of
tNLNH (minimum 150 ns). The same tOPR time is needed before the device is operational
after warm reset. Figure 25 shows the timing of the power on and warm reset.
9.5.3.3
Table 33 shows the I/O pin, register and PLD status during power on reset, warm reset
and power down mode. PLD outputs are always valid during warm reset, and they are
valid in power on reset once the internal PSD configuration bits are loaded. This loading of
PSD is completed typically long before the V
is active, the state of the outputs are determined by the PLD equations.
Figure 25. Power On and Warm Reset Timing
CC
V
RESET
CC
is steady. During this time period the device loads internal configurations, clears
OPERATING LEVEL
I/O Pin, Register and PLD Status at Reset
POWER ON RESET
t NLNH– PO
CC
ramps up to operating level. Once the PLD
t OPR
CC
is below VLKO.
t NLNH
t NLNH-A
WARM
RESET
PSD9XX Family
t OPR
59
Related parts for PSD913F1-B-90JI
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
120V - 100W DMOS AUDIO AMPLIFIER WITH MUTE/ST-BY
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-channel 55V - 0.07 Ohm - 22A StripFET Power MOSFET
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Old PRODUCT: Not Suitable For Design-in
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Programmable poly-phase energy calculator IC
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
High-voltage, High Current Switch
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Single Chip Read & Write Channel
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
10A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
20A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
-
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
ac Line Switch
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Video And Audio Signals Switchings For The Peri-television Plug
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
H/v Deflection With Automatic VCR Switching
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Switch Mode Power Supply Controller
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Stepper Motor Driver
Manufacturer:
ST Microelectronics, Inc.
Datasheet: