AM186ES Advanced Micro Devices, AM186ES Datasheet - Page 45

no-image

AM186ES

Manufacturer Part Number
AM186ES
Description
microcontrollers provide a low-cost/ high-performance solution for embedded system designers who wish to use the x86 architecture.
Manufacturer
Advanced Micro Devices
Datasheets

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AM186ES-20KC
Manufacturer:
AMD
Quantity:
1 045
Part Number:
AM186ES-25KC
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM186ES-25KI/W
Manufacturer:
SICK
Quantity:
1 000
Part Number:
AM186ES-40KC
Manufacturer:
AMD
Quantity:
5 510
Part Number:
AM186ES-40KC
Manufacturer:
XILINX
0
Part Number:
AM186ES-40KC
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM186ES-40VC
Manufacturer:
AMD
Quantity:
1 831
Part Number:
AM186ES25KCW
Manufacturer:
AMD
Quantity:
5 292
Part Number:
AM186ESLV-20KI
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM186ESLV-20VC/W
Manufacturer:
AMD
Quantity:
20 000
Crystal-Driven Clock Source
The internal oscillator circuit of the Am186ER and
Am188ER microcontrollers is designed to function with
a parallel-resonant fundamental mode crystal. Be-
cause of the PLL, the crystal frequency can be twice,
equal to, or one quarter of the processor frequency. Do
not replace a crystal with an LC or RC equivalent. See
Figure 8 for a diagram of oscillator configurations.
The X1 and X2 signals are connected to an internal in-
verting amplifier (oscillator) that provides, along with
the external feedback loading, the necessary phase
shift. In such a positive feedback circuit, the inverting
amplifier has an output signal (X2) 180 degrees out of
phase of the input signal (X1).
The external feedback network provides an additional
180-degree phase shift. In an ideal system, the input to
X1 will have 360 or zero degrees of phase shift. The ex-
ternal feedback network is designed to be as close to
ideal as possible. If the feedback network is not provid-
ing necessary phase shift, negative feedback will
dampen the output of the amplifier and negatively af-
fect the operation of the clock generator. Values for the
loading on X1 and X2 must be chosen to provide the
necessary phase shift and crystal operation.
Selecting a Crystal
When selecting a crystal, the load capacitance should
always be specified (C
ance in the oscillation frequency from the desired spec-
ified value (resonance). The load capacitance and the
loading of the feedback network have the following re-
lationship:
C
L
=
(C
(C
1
1
Notes:
X1 and X2 are not 5-V tolerant. The X1 maximum input is V
+ C
Figure 8. Am186™ER and Am188™ER Microcontrollers Oscillator Configurations
C
a. External Clock Configuration
2
2
)
)
+ C
S
L
). This value can cause vari-
Am186
X1
X2
TM
Am188ER/
Am186ER
Microcontroller
ER and Am188
Oscillator
To PLL
TM
ER Microcontrollers Data Sheet
where C
the crystal and C
fier and tuning these values (C
to oscillate at resonance. Finally, there is a relationship
between C
inverting amplifier, these values need to be offset with
the larger load on the output (X2). Equal values of
these loads will tend to balance the poles of the invert-
ing amplifier.
The characteristics of the inverting amplifier set limits
on the following parameters for crystals:
ESR (Equivalent Series Resistance)60-ohm max
Drive Level .......................... 500-mW max
The recommended range of values for C
as follows:
C
C
The specific values for C
by the designer and are dependent on the characteris-
tics of the chosen crystal and board design.
External Source Clock
Alternately, the internal oscillator can be driven by an
external clock source. The external clock source
should be connected to the input of the inverting ampli-
fier (X1) with the output (X2) left unconnected. X1 and
X2 are not 5-V tolerant and X1 has a maximum input
equal to V
1
2
........................................ 15 pF
........................................ 22 pF
CC
.
S
C
C
is the stray capacitance of the circuit. Placing
1
2
CC
1
and C
.
b. Crystal Configuration
L
in series across the inverting ampli-
2
Crystal
. To enhance the oscillation of the
X1
X2
1
and C
Am188ER/
Am186ER
Microcontroller
1
Oscillator
, C
2
must be determined
To PLL
2
) allows the crystal
20%
20%
1
and C
2
are
45

Related parts for AM186ES