DSPIC30F6010 MICROCHIP [Microchip Technology], DSPIC30F6010 Datasheet - Page 134

• Manufacturer Part Number: DSPIC30F6010
• Description: High-Performance Digital Signal Controllers
• Manufacturer: MICROCHIP [Microchip Technology]

dsPIC30F6010
20.8
The module has 3 internal power modes. When the
ADON bit is ‘1’, the module is in Active mode; it is fully
powered and functional. When ADON is ‘0’, the module
is in Off mode. The digital and analog portions of the
circuit are disabled for maximum current savings. In
order to return to the Active mode from Off mode, the
user must wait for the ADC circuitry to stabilize.
20.9
20.9.1
When the device enters Sleep mode, all clock sources
to the module are shutdown and stay at logic ‘0’.
If Sleep occurs in the middle of a conversion, the con-
version is aborted. The converter will not continue with
a partially completed conversion on exit from Sleep
mode.
Register contents are not affected by the device
entering or leaving Sleep mode.
The A/D module can operate during Sleep mode if the
A/D clock source is set to RC (ADRC = 1). When the
RC clock source is selected, the A/D module waits one
instruction cycle before starting the conversion. This
allows the SLEEP instruction to be executed, which
eliminates all digital switching noise from the conver-
sion. When the conversion is complete, the Done bit
will be set and the result loaded into the ADCBUF
register.
FIGURE 20-3:
DS70119D-page 132
RAM Contents:
Read to Bus:
Signed Fractional (1.15)
Module Power-down Modes
A/D Operation During CPU Sleep
and Idle Modes
A/D OPERATION DURING CPU
SLEEP MODE
Fractional (1.15)
Signed Integer
Integer
A/D OUTPUT DATA FORMATS
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d09 d09 d09 d09 d09 d09 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
0
0
0
0
Preliminary
0
0
If the A/D interrupt is enabled, the device will wake-up
from Sleep. If the A/D interrupt is not enabled, the A/D
module will then be turned off, although the ADON bit
will remain set.
20.9.2
The ADSIDL bit selects if the module will stop on Idle or
continue on Idle. If ADSIDL = 0, the module will con-
tinue operation on assertion of Idle mode. If ADSIDL =
1, the module will stop on Idle.
20.10 Effects of a Reset
A device Reset forces all registers to their Reset state.
This forces the A/D module to be turned off, and any
conversion and acquisition sequence is aborted. The
values that are in the ADCBUF registers are not modi-
fied. The A/D result register will contain unknown data
after a Power-on Reset.
20.11 Output Formats
The A/D result is 10-bits wide. The data buffer RAM is
also 10-bits wide. The 10-bit data can be read in one of
four different formats. The FORM<1:0> bits select the
format. Each of the output formats translates to a 16-bit
result on the data bus.
Write data will always be in right justified (integer)
format.
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
d09 d08 d07 d06 d05 d04 d03 d02 d01 d00
A/D OPERATION DURING CPU IDLE
MODE
 2004 Microchip Technology Inc.
0
0
0
0
0
0
0
0
0
0
0
0