ICS1893 Integrated Circuit Systems, ICS1893 Datasheet - Page 67

no-image

ICS1893

Manufacturer Part Number
ICS1893
Description
3.3-V 10Base-T/100Base-TX Integrated PHYceiver
Manufacturer
Integrated Circuit Systems
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICS1893AF
Manufacturer:
ICS
Quantity:
20 000
Company:
Part Number:
ICS1893AF
Quantity:
30
Part Number:
ICS1893AFILF
Manufacturer:
IDT
Quantity:
110
Part Number:
ICS1893AFLF
Manufacturer:
ICS
Quantity:
20 000
Part Number:
ICS1893AFT
Manufacturer:
IDT
Quantity:
8 000
Part Number:
ICS1893BF
Manufacturer:
ICS
Quantity:
20 000
Part Number:
ICS1893BFI
Manufacturer:
OKI
Quantity:
1 934
Part Number:
ICS1893BFILF
Manufacturer:
ICS
Quantity:
20 000
Part Number:
ICS1893BFLF
Manufacturer:
ICS
Quantity:
409
Part Number:
ICS1893BFLF
Manufacturer:
ICS
Quantity:
20 000
Part Number:
ICS1893BFLFT
Manufacturer:
IDT
Quantity:
8 000
Part Number:
ICS1893BKILFT
Manufacturer:
IDT
Quantity:
5 000
Part Number:
ICS1893BY-10
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
ICS1893BY-10LF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
ICS1893BY-10LFT
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
8.3 Register 1: Status Register
8.3.1 100Base-T4 (bit 1.15)
ICS1893 Rev C 6/6/00
Table 8-6
and an STA. There are two types of status bits: some report the capabilities of the port, and some indicate
the state of signals used to monitor internal circuits.
The STA accesses the Status Register using the Serial Management Interface. During a reset, the
ICS1893 initializes the Status Register bits to pre-defined, default values.
Note:
Table 8-6.
† As per the IEEE Std 802.3u, during any write operation to any bit in this register, the STA must write the default value
The STA reads this bit to learn if the ICS1893 can support 100Base-T4 operations. Bit 1.15 of the ICS1893
is permanently set to logic zero, which informs an STA that the ICS1893 cannot support 100Base-T4
operations.
1.15
1.14
1.13
1.12
1.11
1.10
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
Bit
to all Reserved bits.
ICS1893 - Release
100Base-T4
100Base-TX full duplex
100Base-TX half duplex Mode not supported
10Base-T full duplex
10Base-T half duplex
IEEE reserved
IEEE reserved
IEEE reserved
IEEE reserved
MF Preamble
suppression
Auto-Negotiation
complete
Remote fault
Auto-Negotiation ability
Link status
Jabber detect
Extended capability
For an explanation of acronyms used in
lists the Status Register bits. These 16 bits of data provide an interface between the ICS1893
Status Register (Register 1 [0x01])
Definition
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
Always 0. (Not supported.) N/A
Mode not supported
Mode not supported
Mode not supported
Always 0
Always 0
Always 0
Always 0
PHY requires MF
Preambles
Auto-Negotiation is in
process, if enabled
No remote fault detected
N/A
Link is invalid/down
No jabber condition
N/A
When Bit = 0
67
Table
8-5, see
Mode supported
Mode supported
Mode supported
Mode supported
N/A
N/A
N/A
N/A
PHY does not require
MF Preambles
Auto-Negotiation is
completed
Remote fault detected
Always 1: PHY has
Auto-Negotiation ability
Link is valid/established
Jabber condition
detected
Always 1: PHY has
extended capabilities
When Bit = 1
Chapter 1, “ Abbreviations and Acronyms”
Chapter 8 Management Register Set
cess
Ac-
CW
CW
CW
CW
CW
CW
CW
CW
RO
RO
RO
RO
RO
RO
RO
RO
SF
LH
LH
LH
LL
fault
De-
0†
0†
0†
0†
June, 2000
0
1
1
1
1
0
0
0
1
0
0
1
Hex
7
8
0
9
.

Related parts for ICS1893