m470t2864qz3 Samsung Semiconductor, Inc., m470t2864qz3 Datasheet - Page 12

• Manufacturer Part Number: m470t2864qz3
• Description: Ddr2 Unbuffered Sodimm
• Manufacturer: Samsung Semiconductor, Inc.

10.0 IDD Specification Parameters Definition
(IDD values are for full operating range of Voltage and Temperature)
SODIMM
Symbol
IDD4W
IDD2Q
IDD2N
IDD3N
IDD4R
IDD2P
IDD3P
IDD5B
IDD0
IDD1
IDD6
IDD7
Operating one bank active-precharge current;
tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRASmin(IDD); CKE is HIGH, CS is HIGH between valid commands;
Address bus inputs are SWITCHING; Data bus inputs are SWITCHING
Operating one bank active-read-precharge current;
IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD), tRCD =
tRCD(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data pattern
is same as IDD4W
Precharge power-down current;
All banks idle; tCK = tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE; Data bus inputs are
FLOATING
Precharge quiet standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS is HIGH; Other control and address bus inputs are STABLE; Data
bus inputs are FLOATING
Precharge standby current;
All banks idle; tCK = tCK(IDD); CKE is HIGH, CS is HIGH; Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
Active power-down current;
All banks open; tCK = tCK(IDD); CKE is LOW; Other control and address
bus inputs are STABLE; Data bus inputs are FLOATING
Active standby current;
All banks open; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid
commands; Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
Operating burst write current;
All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP
= tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCHING; Data bus
inputs are SWITCHING
Operating burst read current;
All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRAS-
max(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands; Address bus inputs are SWITCH-
ING; Data pattern is same as IDD4W
Burst auto refresh current;
tCK = tCK(IDD); Refresh command at every tRFC(IDD) interval; CKE is HIGH, CS is HIGH between valid commands;
Other control and address bus inputs are SWITCHING; Data bus inputs are SWITCHING
Self refresh current;
CK and CK at 0V; CKE ≤ 0.2V; Other control and address bus inputs are
FLOATING; Data bus inputs are FLOATING
Operating bank interleave read current;
All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), tRC =
tRC(IDD), tRRD = tRRD(IDD), tFAW = tFAW(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS is HIGH between valid com-
mands; Address bus inputs are STABLE during DESELECTs; Data pattern is same as IDD4R; Refer to the following
page for detailed timing conditions
Proposed Conditions
12 of 19
Fast PDN Exit MRS(12) = 0
Slow PDN Exit MRS(12) = 1
Normal
Low Power
DDR2 SDRAM
Rev. 1.1 July 2008
Units
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Note