mt8vddt3264hdg-335 Micron Semiconductor Products, mt8vddt3264hdg-335 Datasheet - Page 5

• Manufacturer Part Number: mt8vddt3264hdg-335
• Description: 128mb, 256mb, 512mb, 1gb X64, Dr 200-pin Ddr Sodimm
• Manufacturer: Micron Semiconductor Products

Table 8:
PDF: 09005aef80765fab/Source: 09005aef806e1d28
DD8C16_32_64_128x64HD.fm - Rev. D 11/07 EN
RAS#, CAS#, WE#
DQS0–DQS7
CKE0, CKE1
DQ0–DQ63
CK0, CK0#,
DM0–DM7
CK1, CK1#
BA0, BA1
SA0–SA2
Symbol
S0#, S1#
A0–A13
V
Pin Descriptions
SDA
DDSPD
V
V
SCL
V
NC
REF
DD
SS
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
–
128MB, 256MB, 512MB, 1GB (x64, DR): 200-Pin DDR SODIMM
Description
Address inputs: Provide the row address for ACTIVE commands, and the
column address and auto precharge bit (A10) for READ/WRITE commands, to
select one location out of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by BA0, BA1) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA0 and BA1 define which mode register
(mode register or extended mode register) is loaded during the LOAD MODE
REGISTER command. A0–A11 (128MB), A0–A12 (256MB, 512MB),
and A0–A13 (1GB).
Bank address: BA0 and BA1 define the device bank to which an ACTIVE,
READ, WRITE, or PRECHARGE command is being applied.
Clock: CK and CK# are differential clock inputs. All address and control input
signals are sampled on the crossing of the positive edge of CK and the
negative edge of CK#. Output data (DQ and DQS) is referenced to the
crossings of CK and CK#.
Clock enable: CKE HIGH activates and CKE LOW deactivates the internal
clock, input buffers, and output drivers.
Input data mask: DM is an input mask signal for write data. Input data is
masked when DM is sampled HIGH, along with that input data, during a write
access. DM is sampled on both edges of DQS. Although DM pins are input-only,
the DM loading is designed to match that of DQ and DQS pins.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command
being entered.
Chip selects: S# enables (registered LOW) and disables (registered HIGH) the
command decoder.
Presence-detect address inputs: These pins are used to configure the
presence-detect device.
Serial clock for presence-detect: SCL is used to synchronize the presence-
detect data transfer to and from the module.
Data input/output: Data bus.
Data strobe: Output with read data; input with write data. DQS is edge-
aligned with read data, center-aligned with write data. Used to capture data.
Serial presence-detect data: SDA is a bidirectional pin used to transfer
addresses and data into and out of the presence-detect portion of the module.
Power supply: +2.5V ±0.2V (-40B: +2.6V ±0.1V).
Serial EEPROM positive power supply: +2.3V to +3.6V.
SSTL_2 reference voltage (V
Ground.
No connect: These pins are not connected on the module.
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
/2).
Pin Assignments and Descriptions
©2004 Micron Technology, Inc. All rights reserved