k4s643232e-te ETC-unknow, k4s643232e-te Datasheet
k4s643232e-te
Related parts for k4s643232e-te
k4s643232e-te Summary of contents
Page 1
... K4S643232E-TE SDRAM 512K x 32bit x 4 Banks Extended Temperature Samsung Electronics reserves the right to change products or specification without notice. Synchronous DRAM LVTTL(3.3V) 86-TSOP Revision 1.4 December 2001 - 1 - CMOS SDRAM Rev. 1.4 (Dec. 2001) ...
Page 2
... K4S643232E-TE/N Revision History Revision 1.4 (December 4, 2001) • Not supported 90-Ball FBGA Revision 1.3 (October 24, 2001) • Removed CAS Latency 1 from the spec. Revision 1.2 (August 7, 2001) - • Added CAS Latency 1 Revision 1.1 (July 6, 2001) • Added K4S643232E-T/S(E/N)50 Revision 1.0 (April 6, 2001) Revision 0.0 (March 21, 2001) • Initial draft • ...
Page 3
... ORDERING INFORMATION K4S643232E-TE/N50 +85 C K4S643232E-TE/N60 K4S643232E-TE/N70 • - E/N : Extended temperature (-25 Latency & Burst Length Programming Register LWE LCAS Timing Register CS RAS ...
Page 4
... K4S643232E-TE/N PIN CONFIGURATION (Top view TSOP DQM0 A10/AP DQM2 DQ16 V DQ17 DQ18 V DQ19 DQ20 V DQ21 DQ22 V DQ23 DQ0 DDQ DQ1 4 83 DQ2 SSQ DQ3 7 80 DQ4 DDQ DQ5 10 77 DQ6 11 76 ...
Page 5
... K4S643232E-TE/N PIN FUNCTION DESCRIPTION Pin Name CLK System clock CS Chip select CKE Clock enable Address 0 10 BA0,1 Bank select address RAS Row address strobe CAS Column address strobe WE Write enable DQM0 ~ 3 Data input/output mask DQ ~ Data input/output Power supply/ground ...
Page 6
... K4S643232E-TE/N ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on V supply relative to Vss DD Storage temperature Power dissipation Short circuit current Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. ...
Page 7
... K4S643232E-TE/N DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, T Parameter Symbol Operating Current I CC1 (One Bank Active CC2 Precharge Standby Current in power-down mode I PS CC2 I N CC2 Precharge Standby Current in non power-down mode I NS CC2 I P CC3 Active Standby Current in power-down mode ...
Page 8
... K4S643232E-TE/N AC OPERATING TEST CONDITIONS Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition Output 870 (Fig output load circuit 1. The V condition of K4S643232E-60 is 3.135V ~ 3.6V Notes : DD OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) ...
Page 9
... K4S643232E-TE/N Parameter Row active to row active delay RAS to CAS delay Row precharge time Row active time Row cycle time 2. Minimum delay is required to complete write. 3. All parts allow every cycle column address change case of row precharge interrupt, auto precharge and read burst stop. ...
Page 10
... K4S643232E-TE/N SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Entry Refresh Self refresh Bank active & row addr. Read & Auto precharge disable column address Auto precharge enable Write & Auto precharge disable column address Auto precharge enable Burst Stop ...
Page 11
... K4S643232E-TE/N MODE REGISTER FIELD TABLE TO PROGRAM MODES Register Programmed with MRS Address / Function RFU RFU Test Mode A A Type Mode Register Set 0 1 Reserved 1 0 Reserved 1 1 Reserved Write Burst Length Length Burst 1 Single Bit POWER UP SEQUENCE SDRAMs must be powered up and initialized in a predefined manner to prevent undefined operations ...
Page 12
... K4S643232E-TE/N BURST SEQUENCE (BURST LENGTH = 4) Initial Address BURST SEQUENCE (BURST LENGTH = 8) Initial Address Sequential ...