MACH4-96-96-15 Lattice Semiconductor Corp., MACH4-96-96-15 Datasheet - Page 17

• Manufacturer Part Number: MACH4-96-96-15
• Description: High-performance Ee Cmos Programmable Logic
• Manufacturer: Lattice Semiconductor Corp.

ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . .-65 C to +150 C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . .-55 C to +125 C
Device Junction Temperature . . . . . . . . . . . . . +150 C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . . -0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . . -0.5 V to V
DC Output or
I/O Pin Voltage . . . . . . . . . . . . . . -0.5 V to V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current
(T
Stresses above those listed under Absolute Maximum Ratings
may cause permanent device failure. Functionality at or above
these limits is not implied. Exposure to Absolute Maximum
Ratings for extended periods may affect device reliability.
DC CHARACTERISTICS over COMMERCIAL operating ranges
Notes:
1. Total I
2. These are absolute values with respect to device ground and all overshoots due to system or tester noise are included.
3. I/O pin leakage is the worst case of I
4. Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second.
5. Measured with a 16-bit up/down counter pattern. This pattern is programmed in each PAL block and capable of being loaded,
A
Parameter
V
enabled, and reset. An actual I
end of this data sheet.
Symbol
= –40 C to +85 C) . . . . . . . . . . . . . . . . . . . 200 mA
OUT
I
V
I
V
V
V
OZH
I
I
OZL
I
I
OH
SC
CC
IH
OL
IL
IH
IL
= 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
OL
for one PAL block should not exceed 128 mA.
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input HIGH Leakage
Current
Input LOW Leakage
Current
Off-State Output Leakage
Current HIGH
Off-State Output Leakage
Current LOW
Output Short-Circuit
Current
Supply Current
Parameter Description
CC
value can be calculated by using the “Typical Dynamic I
IL
and I
OZL
I
V
I
V
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 2)
Guaranteed Input Logical LOW Voltage for all
Inputs (Note 2)
V
V
V
V
V
V
V
(Note 4)
V
(I
f =25 MHz, T
OH
OL
CC
IN
IN
IN
IN
OUT
IN
OUT
IN
OUT
IN
OUT
(or I
CC
MACH4-96/96-18 (Ind)
= 24 mA, V
= 0 V, Outputs Open
= V
= V
= 5.25 V, V
= 0 V, V
= V
= V
= -3.2 mA, V
+0.5 V
+0.5 V
= 5.25 V, V
= 0 V, V
= 0.5 V, V
= 0 mA), V
IH
IH
IH
IH
IH
and I
or V
or V
or V
or V
CC
A
OZH
CC
IL
IL
IL
IL
= 25 C (Note 5)
CC
CC
= Max (Note 3)
Test Conditions
CC
(Note 1)
(Note 3)
(Note 3)
CC
CC
CC
= Max
).
= Min
= Max (Note 3)
= Max
OPERATING RANGES
Industrial (I) Devices
Temperature (T
in Free Air . . . . . . . . . . . . . . . . . . . . . . –40 C to +85 C
Supply Voltage (V
Respect to Ground. . . . . . . . . . . . . +4.50 V to +5.50 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
= 5.0 V,
= Min
= Max
A
) Operating
CC
) with
CC
Characteristics” Chart towards the
Min
-30
2.4
2.0
Typ
225
Max
-100
-100
-160
0.5
0.8
10
10
V A N T I S
Unit
mA
mA
V
V
V
V
A
A
A
A
17