ST10F273Z4 STMicroelectronics, ST10F273Z4 Datasheet - Page 107
ST10F273Z4
Manufacturer Part Number
ST10F273Z4
Description
16-BIT MICROCONTROLLER WITH MAC UNIT, UP TO 832 KBYTES FLASH MEMORY AND UP TO 68 KBYTES RAM
Manufacturer
STMicroelectronics
Datasheet
1.ST10F273Z4.pdf
(188 pages)
Specifications of ST10F273Z4
Single Voltage Supply
5 V ±10%
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ST10F273Z4Q3
Manufacturer:
INTEL
Quantity:
4 495
Company:
Part Number:
ST10F273Z4Q3
Manufacturer:
STMicroelectronics
Quantity:
10 000
- Current page: 107 of 188
- Download datasheet (2Mb)
ST10F273Z4
21.3.1
In normal running mode (that is when main V
during reset to exercise the EA functionality associated with the same pin: the voltage
supply for the circuitries which are usually biased with V
oscillator used in conjunction with Real-Time Clock module), is granted by the active main
V
It must be noted that Stand-by mode can generate problems associated with the usage of
different power supplies in CMOS systems; particular attention must be paid when the
ST10F273Z4 I/O lines are interfaced with other external CMOS integrated circuits: if V
ST10F273Z4 becomes (for example in Stand-by mode) lower than the output level forced by
the I/O lines of these external integrated circuits, the ST10F273Z4 could be directly powered
through the inherent diode existing on ST10F273Z4 output driver circuitry. The same is valid
for ST10F273Z4 interfaced to active/inactive communication buses during Stand-by mode:
current injection can be generated through the inherent diode.
Furthermore, the sequence of turning on/off of the different voltage could be critical for the
system (not only for the ST10F273Z4 device). The device Stand-by mode current (I
may vary while V
V
phenomenon.
Entering stand-by mode
As already said, to enter Stand-by mode XRAM2EN bit in the XPERCON Register must be
cleared: this allows to freeze immediately the RAM interface, avoiding any data corruption.
As a consequence of a RESET event, the RAM Power Supply is switched to the internal
low-voltage supply V
The RAM interface will remain frozen until the bit XRAM2EN is set again by software
initialization routine (at next exit from main V
Since V
XRAM2EN bit is no longer able to guarantee its content (logic “0”), being the XPERCON
Register powered by internal V
by mode switching dedicated circuit continues to confirm the RAM interface freezing,
irrespective the XRAM2EN bit content; XRAM2EN bit status is considered again when
internal V
If internal V
with bit XRAM2EN set, the RAM Supply switching circuit is not active: in case of a
temporary drop on internal V
no spurious Stand-by mode switching can occur (the RAM is not frozen and can still be
accessed).
The ST10F273Z4 Core module, generating the RAM control signals, is powered by internal
V
switched to V
from ST10F273Z4 Core (active low signal) is low enough to be recognized as a logic “0” by
the RAM interface (due to V
address for the RAM and an unwanted data corruption could occur. For this reason, an extra
interface, powered by the switched supply, is used to prevent the RAM from this kind of
potential corruption mechanism.
DD
DD
18
.
supply; during turning off transient these control signals follow the V
and V
18
18
is falling down (as a consequence of V
STBY
18
comes back over internal stand-by reference V
18SB
becomes lower than internal stand-by reference (V
pins. System noise on both V
DD
internal reference. It could happen that a high level of RAM write strobe
to V
18SB
STBY
(derived from V
18
18
(and vice versa) transition occurs: some current flows between
lower than V
18
voltage versus internal V
. This does not generate any problem, because the Stand-
STBY
18SB
DD
DD
DD
through the low-power voltage regulator).
): The bus status could contain a valid
power-on reset sequence).
is on) the V
and V
DD
turning off), it can happen that the
STBY
18SB
STBY
18SB
STBY
can contribute to increase this
during normal code execution,
(see in particular the 32 kHz
.
18SB
pin can be tied to V
Power reduction modes
) of about 0.3 to 0.45V
18
, while RAM is
STBY
107/188
SS
DD
)
of
Related parts for ST10F273Z4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Encapsulated Dc-dc Converter
Manufacturer:
Arch Electronics
Datasheet:
Part Number:
Description:
16-BIT MCU WITH 32K BYTE ROM
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
Encapsulated DC-DC Converter
Manufacturer:
ARCH [Arch Electronics Corp.]
Datasheet:
Part Number:
Description:
Isolated and Regulated 10 Watt Modular DC/DC Converters
Manufacturer:
ASTRODYNE [Astrodyne Corporation]
Datasheet:
Part Number:
Description:
IC FLASH MEM 256KBIT 144-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT ROMLESS LV 100TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT ROMLESS LV 100-TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 832KBIT FLASH 144-TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 256K FLASH 144PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC MCU 16BIT ROMLESS 144-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC MCU 16BIT LV ROMLESS 100-TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 256K FLASH 144PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 512K FLASH MAC 208-PBG
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 832KBIT FLASH 144-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 16BIT 256KBIT FLASH 144-TQFP
Manufacturer:
STMicroelectronics
Datasheet: