STM8S003F3 STMicroelectronics, STM8S003F3 Datasheet - Page 21

• Manufacturer Part Number: STM8S003F3
• Description: Value line, 16 MHz STM8S 8-bit MCU, 8 Kbytes Flash, 128 bytes data EEPROM
• Manufacturer: STMicroelectronics

Specifications of STM8S003F3

• Program Memory: 8 Kbytes Flash; data retention 20 years at 55 °C after 100 cycles
• Data Memory: 128 bytes of true data EEPROM; endurance up to 100 000 write/erase cycles
• Ram: 1 Kbytes
• Advanced Control Timer: 16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization

STM8S003K3 STM8S003F3
5.2
5.2.1
Pin
no.
28
29
30
31
32
(1)
driven current must respect the absolute maximum ratings (see
(2)
up the device. In this mode, the output state of PA1 is not driven. It is recommended to use PA1 only in input mode if Halt/Active-halt
is used in the application.
(3)
implemented).
(4)
In the open-drain output column, "T" defines a true open-drain I/O (P-buffer, weak pull-up, and protection diode to V DD are not
The PD1 pin is in input pull-up during the reset phase and after internal reset release.
When the MCU is in Halt/Active-halt mode, PA1 is automatically configured in input weak pull-up and cannot be used for waking
I/O pins used simultaneously for high current source/sink must be uniformly spaced around the package. In addition, the total
Pin
name
PD3/
TIM2_CH2/
ADC_ETR
PD4/BEEP/
TIM2_CH1
PD5/
UART1_TX
PD6/
UART1_RX
PD7/ TLI
[TIM1_CH4]
STM8S003F3 TSSOP20/UFQFPN20 pinout and pin description
STM8S003F3 TSSOP20 pinout and pin description
1. HS high sink capability.
Type
I/O
I/O
I/O
I/O
I/O
Input
floating
X
X
X
X
X
wpu
X
X
X
X
X
UART1_CK/TIM2_CH1/BEEP/(HS)PD4
[SPI_NSS] TIM2_CH3/(HS) PA3
UART1_RX/AIN6/(HS) PD6
UART1_TX/AIN5/(HS) PD5
Ext.
interrupt
Figure 4: STM8S003F3 TSSOP20 pinout
X
X
X
X
X
OSCOUT/PA2
DocID018576 Rev 2
Output
High
sink
OSCIN/PA1
HS
HS
HS
HS
HS
NRST
VCAP
V SS
V DD
(1)
Speed
O3
O3
O3
O3
O3
Electrical
1
2
3
4
5
6
7
8
9
10
OD
X
X
X
X
X
characteristics).
12
11
PP
20
19
18
17
16
15
14
13
X
X
X
X
X
PD3 (HS)/AIN4/TIM2_CH2/ADC_ETR
PD2 (HS)/AIN3/[TIM2_CH3]
PD1(HS)/SWIM
PC7
PC6 (HS)/SPI_MOSI [TIM1_CH1]
PC5 (HS)/SPI_SCK [TIM2_CH1]
PC4
PC3 (HS)/TIM1_CH3 [TLI] [TIM1_CH1N]
PB4 (T)/I
PB5 (T)/I
Main
function
(after reset)
(HS)
(HS)
Port D3
Port D4
Port D5
Port D6
Port D7
2
2
/SPI_MISO [TIM1_CH2]
/TIM1_CH4/CLK_CCO/AIN2/[TIM1_CH2N]
C_SCL [ADC_ETR]
C_SDA [TIM1_BKIN]
Pinout and pin description
Default
alternate
function
Timer 2 -
channel 2/ADC
external trigger
Timer 2 -
channel
1/BEEP output
UART1 data
transmit
UART1 data
receive
Top level
interrupt
Alternate
function
after remap
[option bit]
Timer 1 -
channel 4
[AFR6]
21/99