AT90CAN64 Automotive Atmel Corporation, AT90CAN64 Automotive Datasheet - Page 42
AT90CAN64 Automotive
Manufacturer Part Number
AT90CAN64 Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(431 pages)
2.AT90CAN128_AUTOMOTIVE.pdf
(16 pages)
3.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
Specifications of AT90CAN64 Automotive
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
8
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Can
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
8
Input Capture Channels
2
Pwm Channels
7
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT90CAN128_AUTOMOTIVE PDF datasheet #2
- AT90CAN128_AUTOMOTIVE PDF datasheet #3
- Current page: 42 of 431
- Download datasheet (6Mb)
5.6.1
5.7
42
External Clock
AT90CAN32/64/128
Oscillator Calibration Register – OSCCAL
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 5-8.
Note:
• Bit 7 – Reserved Bit
This bit is reserved for future use.
• Bits 6..0 – CAL6..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the internal Oscillator to remove process vari-
ations from the Oscillator frequency. This is done automatically during Chip Reset. When
OSCCAL is zero, the lowest available frequency is chosen. Writing non-zero values to this regis-
ter will increase the frequency of the internal Oscillator. Writing 0x7F to the register gives the
highest available frequency. The calibrated Oscillator is used to time EEPROM and Flash
access. If EEPROM or Flash is written, do not calibrate to more than 10% above the nominal fre-
quency. Otherwise, the EEPROM or Flash write may fail. Note that the Oscillator is intended for
calibration to 8.0 MHz. Tuning to other values is not guaranteed, as indicated in
Table 5-9.
To drive the device from an external clock source, XTAL1 should be driven as shown in
5-4. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Bit
Read/Write
Initial Value
SUT1..0
OSCCAL Value
10
00
01
11
(1)
5-8.
0x3F
0x7F
0x00
1. The device is shipped with this option selected.
Start-up Time from Power-
Start-up times for the internal calibrated RC Oscillator clock selection
Internal RC Oscillator Frequency Range.
R
7
–
0
down and Power-save
CAL6
Min Frequency in Percentage of
R/W
6
6 CK
6 CK
6 CK
<----- -----------
Nominal Frequency
CAL5
R/W
5
100%
50%
75%
Device Specific Calibration Value
CAL4
R/W
4
Additional Delay from
CAL3
Reset (V
R/W
3
Reserved
14 CK + 4.1 ms
14 CK + 65 ms
14 CK
CAL2
CC
R/W
2
= 5.0V)
Max Frequency in Percentage of
----------- ----->
CAL1
R/W
1
Nominal Frequency
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
CAL0
R/W
0
100%
150%
200%
OSCCAL
Table
7682C–AUTO–04/08
5-9.
Figure
Related parts for AT90CAN64 Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MCU AVR 64K FLASH 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 64K FLASH 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
MCU AVR 64K FLASH 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
At90can128 8-bit Avr Microcontroller With 32k Bytes Of Isp Flash And Can Controller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontrollers - MCU 64 KB FLASH - 16MHz
Manufacturer:
Atmel
Part Number:
Description:
8-bit Microcontrollers - MCU Microcontroller
Manufacturer:
Atmel
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet: