UPD3753CY NEC, UPD3753CY Datasheet
UPD3753CY
Available stocks
Related parts for UPD3753CY
UPD3753CY Summary of contents
Page 1
... CCD LINEAR IMAGE SENSOR 22 PIN PLASTIC DIP (400 mil) Please refer to "Quality grade on NEC Semiconductor Devices" (Document number IEI-1209) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications. The information in this document is subject to change without notice. ...
Page 2
BLOCK DIAGRAM •Voltage amplifier •Reset feed-through V 19 OUT level clamp circuit 20 AGND 2 Reset pulse/ clamp pulse generator Optical black (OB) 18 bits, invalid 2 bits, valid photocell 2088 bits, invalid 2 bits CCD register ...
Page 3
... Output unit drain voltage connection connection connection connection connection 8 NC Transfer gate clock connection connection 11 NC PHOTOCELL STRUCTURE DIAGRAM connection 21 No connection NC AGND 20 Analog GND V 19 Output OUT connection connection connection 2 15 Shift register clock Shift register clock 1 DGND 13 Digital GND connection ...
Page 4
ABSOLUTE MAXIMUM RATINGS (T Parameter Output unit drain voltage Shift register clock voltage Transfer gate signal voltage Operating ambient temperature Storage temperature RECOMMENDED OPERATING CONDITIONS (T Parameter Output unit drain voltage Shift register clock 1, 2 signal high level Shift ...
Page 5
ELECTRICAL CHARACTERISTICS MHz, data rate = 1 MHz, storage time = light source: 3200 K halogen lamp + C500 (infrared cut filter), input clock ...
Page 6
TIMING CHART OUT V unstable period OUT 12 bits* Caution Be sure not to use this period (indicated the black level, because this part is unstable. TIMING CHART 90% ...
Page 7
TIMING CHART for TG CROSS POINTS for Note Adjust cross point pin external input resistors. Parameter Remark The ...
Page 8
DEFINITIONS OF CHARACTERISTIC ITEMS 1. Saturation voltage: V sat Output signal voltage at which the response linearity is lost. 2. Saturation exposure: SE Product of intensity of illumination (lx) and storage time (s) when saturation of output voltage occurs. 3. ...
Page 9
Output impedance Output pin impedance viewed from outside. 7. Response: R Output voltage divided by exposure (lx Note that the response varies with the light source. 8. Image Lag: IL The rate between the last output voltage ...
Page 10
STANDARD CHARACTERISTIC CURVES (T DARK OUTPUT TEMPERATURE CHARACTERISTIC 0.5 0.25 0 ° Ambient Temperature 100 400 STORAGE ...
Page 11
POWER SUPPLY VOLTAGE RESPONSE RATIO CHARACTERISTIC 110 100 90 0 4.5 4.7 Power Supply Voltage (V) 5.0 5.3 5.5 PD3753 11 ...
Page 12
APPLICATION EXAMPLE + 0 /16 V 0.1 F PD74HC04 The application circuits and their parameters are for references only and are not intended for use ...
Page 13
PACKAGE DIMENSIONS CCD LINEAR IMAGE SENSOR 22PIN PLASTIC DIP (400 mil) (Unit : mm) 1bit 1.7±0.3 37.5 44.0±0.3 1.02±0.15 0.46±0.1 25.4 2.54 Name Dimensions Plastic cap 42.9 8.35 1 The bottom of the package The surface of the chip 2 ...
Page 14
RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. For more details, refer to our document “SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL” (IEI-1207). Please consult with our sales offices in case other soldering process ...
Page 15
... Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction connection is provided to the input pins possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices ...
Page 16
... The devices listed in this document are not suitable for use in aerospace equipment, submarine cables, nuclear reactor control systems and life support systems. If customers intend to use NEC devices for above applications or they intend to use "Standard" quality grade NEC devices for applications not intended by NEC, please contact our sales people in advance. ...