AMIS49587C5871RG ON Semiconductor, AMIS49587C5871RG Datasheet - Page 39

• Manufacturer Part Number: AMIS49587C5871RG
• Description: IC MODEM PLC 50/60MHZ 28PLCC
• Manufacturer: ON Semiconductor

Specifications of AMIS49587C5871RG

• Baud Rates: Selectable
• Interface: SCI
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 28-PLCC
• Number Of Transmitters: 1
• Power Supply Requirement: Single
• Package Type: PLCC
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 28
• Operating Temperature (max): 70C
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Format: -
• Lead Free Status / Rohs Status: Compliant

Table 41. CONFIGURATION PARAMETERS
NbAlarm
R_ALC_CTRL→Value
Max_Transmitting_Gain→Value
R_ALC_CTRL→Value
Max_Transmitting_Gain→Mode
R_CONF_TX_DATA_PRE_SLOT_SEL
Pad
R_CONF→MODE
R_CONF→BAUDRATE
R_CONF→MAINS_FREQ
Pad
Search method
SINC Filter
SYNCHRO--Type→Mode
SYNCHRO--Bit→Value
SYNCHRO--Bit→Mode
SearchInitiatorGain or
Min--ReceivingGain Mode
Search Initiator Gain or
Min--Receiving Gain
Max--Receiving--Gain→Value
Max--Receiving--Gain→Mode
Time out Inter Character TIC
Bad CRC transmitting
Field
(b7 to b4)
(b3 to b1)
(b5 to b3)
(b3 to b1)
(b6 to b4)
(b3to b1)
1 bit (b0)
1 bit (b7)
1 bit (b6)
1 bit (b7)
1 bit (b5)
1 bit (b4)
1 bit (b0)
1 bit (b7)
1 bit (b0)
1 bit (b7)
1 bit (b6)
Length
(b2, b1)
4 bits
3 bits
3 bits
2 bits
3 bits
3 bits
3 bits
1 bit
1 bit
(b0)
(b6)
http://onsemi.com
Value
XXXX
0000
XXX
XXX
XXX
XXX
001
010
011
00
01
10
11
X
0
1
0
1
0
0
1
0
0
1
0
1
0
1
1
0
0
1
0
1
0
1
39
Number of repetitions of a Phy Alarm
Disable Phy Alarm functionality
Attenuation value in fixed mode
Automatic level control
Fixed mode
The output pin is the PRE_SLOT signal or Mode =
Master
The output pin is the transmitted DATA (for Radio)
This bit is not used (adjust length at 1 byte)
Master mode for client station
Slave mode for server station
Monitor mode to spy and test of the DLC
communication
300 baud @ 50 Hz or 360 baud @ 60 Hz
600 baud @ 50 Hz or 720 baud @ 60 Hz
1200 baud @ 50 Hz or 1440 baud @ 60 Hz
2400 baud @ 50 Hz or 2880 baud @ 60 Hz
mains frequency = 50 Hz
mains frequency = 60 Hz
This bit is not used (adjust length at 1 byte)
Method V6, favors FSK
Method V3, favors ASK
Disabled
Enabled
Must be set to 0 (Synchronization on sub--frame
preamble)
Synchro--bit value (in chip clock) in fixed mode
Must be set to 1 (Fixed synchro bit)
Search Initiator Gain selected
Min Receiving Gain selected
Value of the gain for Intelligent Synchronization or Min
Receiving Value Min Gain of reception = (value * 6 db)
Max Receiving gain value in limited mode Range of
reception = (value * 6 db)
Non limited Max--Receiving--Gain
Limited Max--Receiving--Gain
Constant of 10 ms
5 characters depending on communication speed
Disables the transmitting of bad CRC frames
Enables the transmitting of bad CRC frames
Monitor: Don’t care
Description