MC145574AAC Freescale Semiconductor, MC145574AAC Datasheet - Page 52

• Manufacturer Part Number: MC145574AAC
• Description: IC TRANSCEIVER ISDN 32-LQFP
• Manufacturer: Freescale Semiconductor
• Type: Transceiverr

Specifications of MC145574AAC

• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Package / Case: 32-LQFP
• Number Of Line Interfaces: 1
• Control Interface: HDLC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Protocol: -
• Lead Free Status / Rohs Status: Compliant

6–6
6.5.1
6.5.2
6.5
GCI DIRECT MODE
The alternative GCI mode is direct mode. This mode should be used when a fully–compliant GCI
is required. In this mode, the SCP interface is not available.
In a GCI direct mode the monitor, C/I, and A/E channels are fully active and compatible with the GCI
standards.
To enter a GCI direct mode, the SCPEN/GCIEN pin should be tied to V SS and a reset applied to the
device. The GCI direct mode is selected on the rising edge of RESET. The GCIEN pin must be tied
to V SS at all times when GCI direct mode is the required mode of operation. The GCIEN pin is continu-
ously sampled internally. A “zero–to–one” transition on GCIEN will cause the MC145574 to exit from
a GCI direct mode into IDL/SCP mode.
In GCI direct mode, the IRQ function is not required and is internally disabled.
On entering GCI direct mode, the pins of the MC145574 are redefined as follows.
Slave Mode
In the slave mode, DCL and FSC are inputs. DCL can be any frequency between 512 kHz and
4.096 MHz. In the slave mode, S2, S1, and S0 pins control the timeslot in which the device operates.
In the NT slave mode, it is possible to select both NT1 Star and NT Terminal modes via the Monitor
channel. The associated pins used in the default IDL2 mode are enabled and operate in the same
manner.
In the TE slave mode, the TFSC/TCLK pin is enabled and it is possible to select the TCLK and its
frequency via the Monitor channel.
Master Mode
In the master mode, DCL and FSC are outputs. The M2, M1, and M0 pins control mode selection
in master mode; however, these modes are defined differently for the NT and TE master.
SCPEN changes to GCIEN (an input).
FST changes to BCL (an output).
SCPCLK changes to S2 (an input) in slave mode, and M2 (an input) in master mode.
SCP Rx changes to S1 (an input) in slave mode, and M1 (an input) in master mode.
SCP Tx changes to S0 (an input) in slave mode, and M0 (an input) in master mode.
DGRANT changes to SG (an output) in TE master mode.
BCL is enabled in both the slave and master mode. BCL is an output clock which is the DCL
clock divided by two. BCL is synchronous with FSC and can be used by non–GCI devices which
require a locked bit frequency clock to access the B and D channel slots (i.e., codec).
Freescale Semiconductor, Inc.
Table 6–3. M2, M1, and M0 Pins in GCI NT Master Mode
M2
For More Information On This Product,
0
0
0
0
1
1
1
1
Go to: www.freescale.com
M1
0
0
1
1
0
0
1
1
MC145574
M0
0
1
0
1
0
1
0
1
DCL = 2.048 MHz, Channel 0
DCL = 2.048 MHz, Channel 1
DCL = 2.048 MHz, Channel 2
DCL = 2.048 MHz, Channel 3
DCL = 1.536 MHz, Channel 0
DCL = 1.536 MHz, Channel 1
DCL = 1.536 MHz, Channel 2
DCL = 512 kHz, Channel 0
GCI NT Master Mode
MOTOROLA