ITV2050-01F3N-Q SMC Corporation, ITV2050-01F3N-Q Datasheet - Page 26

• Manufacturer Part Number: ITV2050-01F3N-Q
• Description: Regulator; 1500L/min; .005-.9MPa range; 24VDC; 3/8G(PF) ports; 1-5VDC out
• Manufacturer: SMC Corporation

Specifications of ITV2050-01F3N-Q

• Pressure, Operating: 0.9 Mpa
• Size, Port: 3⁄8 "
• Temperature, Ambient: 0 to 50 °C
• Thread Type: G(PF)

∗ For safety reasons, it is recommended that one of the preset pressures be
Connect the cable to the connector on the body
with the wiring arranged as shown below.
Proceed carefully, as incorrect wiring can
cause damage.
Further, use DC power with sufficient capacity
and a low ripple.
Note) A right angle type cable is also available.
One of the preset pressures P1 through P4 is selected by the ON/OFF
combination of S1 and S2.
Wiring diagram
Vs: Power supply 24 VDC
Preset input type
Preset pressure
set to 0 MPa.
Brown
Blue
White
Black
Current signal type
Voltage signal type
Vs
1
2
3
4
The entry direction for the right angle type connector is to the left (SUP
port side).
Never turn the connector as it is not designed to turn.
Vs: Power supply 24 VDC
A : Input signal
Current signal type
Caution
Vs
S1
S2
A
Body
Brown
White
Blue
Black
Note)
S1
S2
Power supply
Input signal
GND (COMMON)
Monitor output
12 to 15 VDC
OFF
OFF
P1
Series
Specific Product Precautions 2
Be sure to read before handling.
Brown
Blue
White
Black
Brown
Blue
White
Black
12 to 15 VDC
4 to 20 mADC
0 to 20 mADC
OFF
ON
P2
OFF
ON
P3
ITV1000/2000/3000
ON
ON
P4
Preset input type
4: (Black)
1
2
3
4
Voltage signal type
Vs : Power supply 24 VDC
Vin: Input signal
3: (Blue)
Vs
Vin
Brown
White
Blue
Black
RESET
Power supply
Input signal
GND (COMMON)
Monitor output
1: (Brown)
2: (White)
Brown
Blue
White
Black
12 to 15 VDC
0 to 5 VDC
0 to 10 VDC
Wiring
Monitor output wiring diagram
∗ When 30 mA DC or more is applied, detecting device for overcurrent starts
The regulating pressure range, by unit of standard
measured pressure, is shown in the table below.
Regulating pressure range, by unit of standard measured pressure
activating and then emits an error signal.
(Error number “5”)
kgf/cm
MPa
Unit
kPa
PSI
bar
2
Analog output, voltage type
Switch output, NPN type
Switch output, PNP type
Analog output, current type (sink type)
0.005 to
0.05 to
0.05 to
0.7
5
Monitor output current
Monitor output current
Set Pressure Range
ITV 01
to 15
to 100
Load
Load
0.1
1
1
Regulating pressure range
∗
∗
0.005 to
0.05 to
0.05 to
0.7
5
ITV 03
to 70
to 500
0.5
5
5
Brown
Blue
White
Black
Brown
Blue
White
Black
Brown
Blue
White
Black
Brown
Blue
White
Black
0.005 to
0.05 to
0.05 to
0.7
5
ITV 05
14-8-29
to 130
to 900
0.9
9
9
F.R.L.
AV
AU
AF
AR
IR
VEX
AMR
ITV
IC
VBA
VE„
VY1
G
PPA
AL