ITV2050-01F3N-Q SMC Corporation, ITV2050-01F3N-Q Datasheet - Page 25

• Manufacturer Part Number: ITV2050-01F3N-Q
• Description: Regulator; 1500L/min; .005-.9MPa range; 24VDC; 3/8G(PF) ports; 1-5VDC out
• Manufacturer: SMC Corporation

Specifications of ITV2050-01F3N-Q

• Pressure, Operating: 0.9 Mpa
• Size, Port: 3⁄8 "
• Temperature, Ambient: 0 to 50 °C
• Thread Type: G(PF)

1. Do not use a lubricator on the supply side of
1. Employ suitable protective measures in
2. Consult SMC when used in power plants, or
1. Install an air filter near this product on the
2. Compressed air containing large amounts of
3. If large amounts of carbon dust are gener-
2. If electric power is shut off while pressure is
3. If power to this product is cut off due to a
14-8-28
locations where there is contact with water
droplets, oil or welding spatter, etc.
if instrumentation related.
supply side. Select a filtration degree of 5
µm or less.
drainage can cause malfunction of this
product and other pneumatic equipment. As
a countermeasure, install an aftercooler, air
dryer or Drain Catch, etc.
ated by the compressor, it can accumulate
inside this product and cause malfunction.
For details on the above compressed air
quality, refer to Best Pneumatics Vol. 16.
this product, as this can cause malfunction.
When lubrication of terminal equipment is
necessary, connect a lubricator on the out-
put side of this equipment.
being applied, pressure will be retained on
the output side.
However, this output pressure is held only
temporarily and is not guaranteed. If ex-
hausting of this pressure is desired, shut off
the power after reducing the set pressure,
and discharge the air using a residual pres-
sure exhaust valve, etc.
power failure, etc. when it is in a controlled
state, output pressure will be retained
temporarily. Handle carefully when operating
with output pressure released to the
atmosphere, as air will continue to flow out.
Warning
Caution
Caution
Operating Environment
Series
Specific Product Precautions 1
Be sure to read before handling.
Air Supply
Handling
ITV1000/2000/3000
10. Due to the large volume of the output side, a
11. Specifications on page 1 is in case of static
12. For details on the handling of this product,
5. In this product, the output side pressure can-
6. This product is adjusted for each specifica-
7. The optional cable connector is a 4 wire type.
8. Please note that the right angle cable does
9. Take the following steps to avoid malfunc-
4. If supply pressure to this product is
interrupted while the power is still on, the
internal solenoid valve will continue to
operate and a humming noise may be
generated. Since the life of the product may
be shortened, shut off the power supply also
when supply pressure is shut off.
not be completely relieved within the range
of 0.005 MPa or less. If it is desired to reduce
the pressure completely to 0 MPa, install a 3
way valve or other device on the output side
to exhaust the pressure.
tion at the time of shipment from the factory.
Avoid careless disassembly or removal of
parts, as this can lead to malfunction.
When the monitor output (analog output or
switch output) is not being used, keep it from
touching the other wires as this can cause
malfunction.
not rotate and is limited to only one entry
direction.
tion due to noise.
1) Remove power supply noise during operation by installing a
2) For avoiding the influence of noise install this product and its
3) Be sure to implement protective measures against load
4) Install or remove the connector after shutting off the power
loud exhaust noise will be produced when
being used for the purpose of a relief
function. Therefore, install a silencer (SMC
Series AN200 or AN400) on the exhaust port
(EXH port). The port sizes are Rc1/8, Rc1/4
and Rc1/2.
environment. Pressure may fluctuate when
air is consumed at the output side.
refer to the instruction manual which is
included with the product.
line filter, etc. in the AC power line.
wiring as far as possible from strong electric fields such as
those of motors and power lines, etc.
surge for induction loads (solenoid valves, relays, etc.).
supply to avoid the influence of chattering of the power
supply.
Caution
Handling