CS42L51-CNZ Cirrus Logic Inc, CS42L51-CNZ Datasheet - Page 35

• Manufacturer Part Number: CS42L51-CNZ
• Description: IC CODEC STEREO W/HDPN AMP 32QFN
• Manufacturer: Cirrus Logic Inc
• Type: Stereo Audior

Specifications of CS42L51-CNZ

• Package / Case: 32-QFP
• Data Interface: PCM Audio Interface
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 98 / 98
• Voltage - Supply, Analog: 1.8V, 2.5V
• Voltage - Supply, Digital: 1.8V, 2.5V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 6
• Number Of Dac Outputs: 2
• Conversion Rate: 96 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, I2C, SPI)
• Resolution: 24 bit
• Operating Supply Voltage: 1.8 V / 2.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 2 ADC/2 DAC
• Thd Plus Noise: - 88 dB ADC / - 86 dB DAC
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1005 - BOARD EVAL FOR CS42L51 CODEC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1045

DS679F1
4.4.2
4.4.3
4.4.4
Volume Controls
Three digital volume control functions are implemented, offering independent control over the ADC and
PCM signal paths into the mixer as well as a combined control over the mixed signals. All volume controls
are programmable to ramp in increments of 0.125 dB at a rate controlled by the DAC soft ramp/zero cross
settings.
All signal paths may also be independently muted via mute control bits. When enabled, each bit attenu-
ates the signal to its maximum value. When the mute bit is disabled, the signal returns to the attenuation
level set in the respective volume control register. The attenuation is ramped up and down at the rate
specified by the DAC_SZC[1:0] bits.
Mono Channel Mixer
A channel mixer may be used to create a mix of the left and right channels for either the PCM or ADC
signals. This mix allows the user to produce a MONO signal from a stereo source. The mixer may also be
used to implement a left/right channel swap.
Beep Generator
The Beep Generator generates audio frequencies across approximately two octave major scales. It offers
three modes of operation: Continuous, multiple and single (one-shot) beeps. Sixteen on and eight off
times are available.
Note: The Beep is generated before the limiter and may affect desired limiting performance. If the limiter
function is used, it may be required to set the Beep volume sufficiently below the threshold to prevent the
peak detect from triggering. Since the master volume control, AOUTx_VOL[7:0], will affect the Beep vol-
ume, DAC volume may alternatively be controlled using the PCMMIXx_VOL[6:0] bits.
Software
Controls:
Software
Controls:
Software
Controls:
“ADCx Mixer Volume Control: ADCA (Address 0Eh) & ADCB (Address 0Fh)” on page
Mixer Volume Control: PCMA (Address 10h) & PCMB (Address 11h)” on page
ume Control: AOUTA (Address 16h) & AOUTB (Address 17h)” on page
(Address 08h)” on page
“PCM Channel Mixer (Address 18h)” on page
(Address 13h)” on page
“Beep Frequency & Timing Configuration (Address 12h)” on page
-10dB
Gain
0dB
dB
Figure 14. De-Emphasis Curve
3.183 kHz
T1=50 µs
F1
57.
63,
“Beep Configuration & Tone Configuration (Address 14h)” on page 64
10.61 kHz
F2
T2 = 15 µs
Frequency
67.
62,
“Beep Off Time & Volume
66,
“DAC Output Control
62,
“AOUTx Vol-
CS42L51
61,
“PCMX
35