MPC8360EVVAJDGA Freescale Semiconductor, MPC8360EVVAJDGA Datasheet - Page 99

• Manufacturer Part Number: MPC8360EVVAJDGA
• Description: IC MPU POWERQUICC II PRO 740TBGA
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC II PROr

Specifications of MPC8360EVVAJDGA

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 533MHz
• Voltage: 1.2V
• Mounting Type: Surface Mount
• Package / Case: 740-TBGA
• Processor Series: MPC8xxx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: MPC8360E-RDK
• Maximum Clock Frequency: 533 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• I/o Voltage: 1.8 V, 2.5 V, 3.3 V
• Minimum Operating Temperature: 0 C
• Core Size: 32 Bit
• Program Memory Size: 64KB
• Cpu Speed: 533MHz
• Embedded Interface Type: I2C, SPI, USB, UART
• Digital Ic Case Style: TBGA
• No. Of Pins: 740
• Rohs Compliant: Yes
• For Use With: MPC8360EA-MDS-PB - KIT APPLICATION DEV 8360 SYSTEMMPC8360E-RDK - BOARD REFERENCE DESIGN FOR MPC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

(edge) of the package will be approximately the same as the local air temperature near the device.
Specifying the local ambient conditions explicitly as the board temperature provides a more precise
description of the local ambient conditions that determine the temperature of the device. At a known board
temperature, the junction temperature is estimated using the following equation:
where:
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction
temperature can be made. The application board should be similar to the thermal test condition: the
component is soldered to a board with internal planes.
23.2.3
To determine the junction temperature of the device in the application after prototypes are available, the
Thermal Characterization Parameter (Ψ
measurement of the temperature at the top center of the package case using the following equation:
where:
The thermal characterization parameter is measured per JESD51-2 specification using a 40 gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
23.2.4
In some application environments, a heat sink will be required to provide the necessary thermal
management of the device. When a heat sink is used, the thermal resistance is expressed as the sum of a
junction to case thermal resistance and a case to ambient thermal resistance:
where:
Freescale Semiconductor
MPC8360E/MPC8358E PowerQUICC II Pro Processor Revision 2.x TBGA Silicon Hardware Specifications, Rev. 4
T
T
R
P
T
T
Ψ
P
R
J
B
J
T
θ
D
D
θ
JT
JA
JA
= junction temperature (°C)
= junction temperature (°C)
= thermocouple temperature on top of package (°C)
= board temperature at the package perimeter (°C)
= power dissipation in the package (W)
= power dissipation in the package (W)
Experimental Determination of Junction Temperature
Heat Sinks and Junction-to-Ambient Thermal Resistance
= junction-to-ambient thermal resistance (°C/W)
= junction to board thermal resistance (°C/W) per JESD51-8
= junction-to-ambient thermal resistance (°C/W)
T
T
R
J
J
θ
JA
= T
= T
= R
B
T
+ (
+ (R
θ
JC
Ψ
θ
JT
+ R
JB
× P
× P
θ
CA
D
D
)
)
JT
) can be used to determine the junction temperature with a
Thermal
99