XE8802MI035LF Semtech, XE8802MI035LF Datasheet - Page 190

• Manufacturer Part Number: XE8802MI035LF
• Description: IC DAS 16BIT FLASH 8K 100-LQFP
• Manufacturer: Semtech

Specifications of XE8802MI035LF

• Applications: Sensing Machine
• Core Processor: RISC
• Program Memory Type: FLASH (22 kB)
• Controller Series: XE8000
• Ram Size: 1K x 8
• Interface: SPI, UART
• Number Of I /o: 36
• Voltage - Supply: 2.4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• For Use With: XE8000MP - PROG BOARD AND PROSTART2 CARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The cmpd peripheral is a 4-channel low power comparator. It is intended to compare analog input signals with an
internally set threshold voltage. The comparator maintains low current consumption even if the input signal is very
close to the threshold. The comparison result of each channel can be used to generate an interrupt and/or is
available for polling.
The comparator can be enabled or disabled by programming the Enable bit in the RegCmpdCtrl register. When
disabled, the block consumes no current.
The peripheral has a single interrupt output which is a combination of the four channels. The combination can be
chosen by programming the RegCmpdCtrl register. The EnIrqCh[3:0] bits select the channel that can activate the
interrupt. The IrqOnRisingCh[2:0] bits indicate if the interrupt is generated on detection of the rising or falling edge
of the channel.
The comparison results of the peripheral can be read in the RegCmpdStat register. The bits CmpdOut[3:0] are
the value of the comparisons at the moment the register is read. The CmpdStat[3:0] indicates which channel
generated an interrupt since the register was last read.
Comparator specifications:
Comments:
1. The quiescent current is defined for a static input voltage <0.5V or >1.3V. The specified consumption is the
2. The maximal static current is defined for any static input voltage between VDD and VSS. The specified
3. Defined with respect to VSS.
How to start the cmpd:
To avoid unwanted irqs one has first to configure the rising / falling edge of the detection (bit IrqOnRisingCh[2:0])
and to enable the comparator (bit Enable). Only after that may the user enable the channel interrupts with bit
EnIrqCh[3:0].
22.3 Register map
There are two registers in the Cmpd, namely RegCmpdStat and RegCmpdCtrl. Table 22-3 and Table 22-4 show
the mapping of the control bits and the functionality of these registers.
© Semtech 2006
sum for all 4 channels.
consumption is the sum for all 4 channels.
t
IDD
IDD
V
∆V
V
pulse
th
hyst
Sym
th
q
stat
/∆T
Required input pulse width
Quiescent current
Maximal static current
Threshold voltage
Threshold temperature drift
Threshold hysteresis
description
Table 22-1: Comparator specifications
XE8802 Sensing Machine Data Acquisition MCU
RegCmpdStat
RegCmpdCtrl
Table 22-2: Cmpd registers
register name
22-3
min
500
0.7
with ZoomingADC™ and LCD driver
-0.9
typ
0.8
1.5
13
max
1.5
1.1
ns
µA
µA
V
mV/°C
mV
unit
3
VBAT≥1.2V
1
2
comments
www.semtech.com