SI5338M-A-GMR Silicon Laboratories Inc, SI5338M-A-GMR Datasheet - Page 24

• Manufacturer Part Number: SI5338M-A-GMR
• Manufacturer: Silicon Laboratories Inc

Si5338
3.9.2. Output Phase Increment/Decrement
The Si5338 has a digitally-controlled glitchless phase
increment and decrement feature that allows adjusting
the phase of each output clock in relation to the other
output clocks. The phase of each output clock can be
adjusted with an accuracy of 20 ps over a range of
±45 ns. Setting of the step size and control of the phase
increment or decrement is accomplished through the
I
with optional phase increment (PINC) and phase
decrement (PDEC) pins for pin-controlled applications.
In pin controlled applications the phase increment and
decrement update rate is as fast as 1.5 MHz. In I
applications, the maximum update rate is limited by the
speed of the I
of pin-controlled devices.
The phase increment and decrement feature provides a
useful method for fine tuning setup and hold timing
margins or adjusting for mismatched PCB trace lengths.
3.9.3. Initial Phase Offset
Each output clock can be set for its initial phase offset
up to ±45 ns. In order for the initial phase offset to be
applied correctly at power up, the VDDOx output supply
voltage must cross 1.2 V before the VDD (pins 7,24)
core power supply voltage crosses 1.45 V. This applies
to the each driver output individually. A soft_reset will
also guarantee that the programmed Initial Phase Offset
is applied correctly. The initial phase offset only works
on outputs that have their R divider set to 1.
3.9.4. Output R Divider
When the requested output frequency of a channel is
below 5 MHz, the Rn (n = 0,1,2,3) divider needs to be
set and enabled. This is automatically done in register
maps generated by the ClockBuilder Desktop. When
the Rn divider is active the step size range of the
frequency increment and decrement function will
decrease by the Rn divide ratio. The Rn divider can be
set to {1, 2, 4, 8, 16, 32}.
24
2
C interface. Alternatively, the Si5338 can be ordered
2
C. See Table 18 for ordering information
2
Rev. 0.6
C
Non-unity settings of R0 will affect the Finc/Fdec step
size at the MultiSynth0 output. For example, if the
MultiSynth0 output step size is 2.56 MHz and R0 = 8,
the step size at the output of R0 will be 2.56 MHz
divided by 8 = .32 MHz. When the Rn divider is set to
non-unity, the initial phase of the CLKn output with
respect to other CLKn outputs is not guaranteed.
3.9.5. Zero-Delay Mode
The Si5338 supports an optional zero delay mode of
operation for applications that require minimal input-to-
output delay. In this mode, one of the device output
clocks is fed back to the feedback input pin (IN4 or IN5/
IN6) to implement an external feedback path essentially
nullifying the delay between the reference input and the
output clocks. Figure 14 shows the Si5338 in a typical
zero-delay configuration. It is generally recommended
that Clk3 be LVDS and that the feedback input be pins 5
and 6. For the differential input configuration to pins 5
and 6, see Figure 3 on page 17. The zero-delay mode
combined with the phase increment/decrement feature
allows unprecedented flexibility in generating clocks
with precise edge alignment.
Input
Clk
Figure 14. Si5338 in Zero Delay Clock
P1
P2
Generator Mode
PLL
Si5338
M0
M1
M2
M3
R0
R1
R2
R3
Clk0
Clk3
Clk1
Clk2