LQ230M1LW11 Sharp Electronics, LQ230M1LW11 Datasheet
LQ230M1LW11
Specifications of LQ230M1LW11
Related parts for LQ230M1LW11
LQ230M1LW11 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ230M1LW11 TFT-LCD Module Spec. Issue Date: March 8, 2006 AVC Liquid Crystal Displays Group No: LD-18280 ...
Page 2
...
Page 3
...
Page 4
... Application This technical literature applies to the color 23.0” WUXGA TFT-LCD module LQ230M1LW11. * These technical literature are proprietary products of SHARP CORPORATION (“SHARP”) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, LED control circuit, LED back light system ...
Page 6
Input Terminals 4-1. Control circuit driving CN1 (Interface signals and +12V DC power supply ; Shown in Fig.1,2) Using connector ： FI-X30SSL-HF (Japan Aviation Electronics Ind. , Ltd.) 【 Note1】 Matching connector ： FI-X30H,FI-X30C or FI-X30M (Japan Aviation Electronics ...
Page 7
Note1】 pin assignment with LVDS_SET pin DS90CF383 or C385 (National semiconductor) ...
Page 8
RA1 RA0 GA2 GA1 BA3 BA2 RA7 RA6 RB1 RB0 GB2 GB1 BB3 BB2 RB7 RB6 NA: Not Available GA0 RA5 RA4 RA3 RA2 BA1 BA0 GA5 GA4 GA3 DEA NA NA BA5 BA4 NA BA7 BA6 GA7 GA6 GB0 ...
Page 9
RA3 RA2 GA4 GA3 BA5 BA4 RA1 RA0 RB3 GB4 BB5 RB1 NA: Not Availabl GA2 RA7 RA6 RA5 BA3 BA2 GA7 GA6 DEA NA NA BA7 NA BA1 BA0 GA1 RB2 GB2 RB7 RB6 RB5 GB3 BB3 BB2 GB7 ...
Page 10
RSDS LVDS → LVDS TTL → RSDS LVDS → LVDS TTL → ...
Page 11
LED back light driving. CN-1 Supplying for LED Power. (Shown in Fig.1,2) Using connector Matching connector PHR-10 JST 1 V LED 2 V LED +24V DC power supply for LED driving LED 4 V LED 5 GND ...
Page 12
LCD Module Block Diagram Input signals (LVDS Dual) RXO0+ RXE0+ RXO0- RXE0- RXO1+ RXE1+ RXO1- RXE1- LVD RXO2+ RXE2+ Receiver RXO2- RXE2- RXO3+ RXE3+ RXO3- RXE3- DC/DC RXOC+ RXEC+ RXOC- RXEC- Bias voltage HRC OFF SEL LVDS Vcc1 (+12V) ...
Page 13
Electrical Characteristics 6-1. TFT-LCD panel driving Parameter Supply voltage Current dissipation Differential input threshold voltage(High) Differential input threshold voltage(Low) Input signal voltage 【 Note 1】 1) Input voltage sequences 0.1ms≦t1 ≦20ms, 1ms≦t2≦40ms 0ms≦t3≦40ms, t4≧0.5s t5≧0ms, 0ms≦t6≦40ms, 2) Dip conditions ...
Page 14
LED driving for back light The back light system is side-lighting type with 102 LEDs . Parameter Supply Voltage ＋24V Current dissipation (for LED drive) Rush current +5V Supply voltage (OFF) (for LED control) Current dissipation Permissive input ripple ...
Page 15
Timing characteristics of input signals 7-1. Timing characteristics Timing diagrams of input signal are shown in Fig.7.1 Parameter Frequency Clock Skew Horizontal period Horizontal period (High) Data enable Vertical period signal Vertical period (High) 【 Note1】 LVDS(A port data)-LVDS(B ...
Page 16
Input data signal and display position on the screen Disp lay posit input dat a(H, V) ...
Page 17
Input Signal, Basic Display Colors and Gray Scale of Each Color Color & Gray Gray ...
Page 18
Optical characteristics Ta=25℃, Vcc=+5. =＋12.0V, Brightness=MAX INV Parameter Symbol θ21, Horizontal Viewing angle θ22 range θ11 Vertical θ12 θ ⊿ Horizontal θ ⊿ Color Shift θ Vertical θ ⊿ CRn Contrast ratio τr +τd θ= 0° Response ...
Page 19
Note 1】 Definitions of viewing angle range : 【 Note 2】 Definition of contrast ratio : The contrast ratio is defined as the following. Contrast Ratio (CR) = 【 Note 3】 Definition of response time The response time is ...
Page 20
Note 6】 θ is the angle that the average of ⊿ ⊿ u’v’. means color difference compared with front direction ...
Page 21
... By using IIC-bus (CN-2), the brightness and the color temperature are able to control. 10-1 Normal operating mode 10-1-1 Normal operating procedure flow chart. START Step 1: Software reset Step 2: Read calibration data from EEPROM (EEPROM is mounted on LQ230M1LW11) Step 3: Write calibration data to control register. Step 4: Select color space Step 5: Send color set point ...
Page 22
Normal operating steps. Step Step IIC Data Sequence 1.1 S[0xA8][0x01][0x01]P ST 1.2 S[0xA8][0x09]S[0xA9][ 2.1 S[0xA0][0x00]S[0xA1][C0]P 2.2 S[0xA0][0x01]S[0xA1][C1]P 2.3 S[0xA0][0x02]S[0xA1][C2]P 2.4 S[0xA0][0x03]S[0xA1][C3]P 2.5 S[0xA0][0x04]S[0xA1][C4]P 2.6 S[0xA0][0x05]S[0xA1][C5]P 2.7 S[0xA0][0x06]S[0xA1][C6]P 2.8 S[0xA0][0x07]S[0xA1][C7]P 2.9 S[0xA0][0x08]S[0xA1][C8]P 2.10 S[0xA0][0x09]S[0xA1][C9]P 2.11 S[0xA0][0x0A]S[0xA1][C10]P 2.12 ...
Page 23
Step Step IIC Data Sequence C0 3.1 S[0xA8][0x8A][ ]P C1]P 3.2 S[0xA8][0x8B][ C2]P 3.3 S[0xA8][0x8C][ C3]P 3.4 S[0xA8][0x8D][ C4]P 3.5 S[0xA8][0x8E][ 3.6 S[0xA8][0x8F][ C5]P C6]P 3.7 S[0xA8][0x90][ C7]P 3.8 S[0xA8][0x91][ C8]P 3.9 S[0xA8][0x92][ C9]P 3.10 S[0xA8][0x93][ C10]P ...
Page 24
Change white point 10-2-1 Change white point flow chart. START Step 1: Set color space to Yxy Step 2: Send color set point Step 3: Update 10-2-2 Change white point steps. Step IIC Data Sequence 1. S[0xA8][0x04][0x02]P 2.1 S[0xA8][0xEA][0x39]P, ...
Page 25
Change brightness 10-3-1 Change brightness flow chart. START Set brightness. 10-3-1 Change brightness flow chart. Step IIC Data Sequence BR 1. S[0xA8][0xC4][ ]P Step 1: END Program S[0xA8][0xC4][BR]P BR represents the brightness value. The default brightness value is 255 ...
Page 26
Display Quantity The display quality of the color TFT-LCD module shall be in compliance with the incoming inspection Standard. 12. Handling Precautions of the module a) Since the panel is made of glass, it may break or crack if ...
Page 27
Ground attachment to the LCD module should be considered, so that influences from EMI and outer noise is minimized. i) The module has some printed circuit boards (PCBs) on the back side, take care to keep them form any ...
Page 28
Excessive force should not be applied to the screen or the rear side of the LCD module. Excessive pressure on the screen caused by the installation of the LCD module may deteriorate ...
Page 29
Reliability test items No Test item 1 High temperature storage test 2 Low temperature storage test 3 High temperature & high humidity operation test 4 High temperature operation test 5 Low temperature operation test 6 Vibration test (non- operating) ...
Page 30
... Characters are Black. 2) Packing Label 社内品番： （ ４ Ｓ ） LQ230M1LW11 Bar code（ ①） Ｌ ｏ ｔ Ｎ Ｏ ． ： （ １ Ｔ ） ２ ０ ０ ６ ． ※． ※※ ...
Page 31
Carton storage conditions Temperature Humidity 95%RH or less Reference condition : the total storage time (40 ,95%RH) : 240H or less Sunlight Be sure to shelter a product from the direct sunlight. Atmosphere ...
Page 32
...
Page 33
...
Page 34
Fig.3 PACKING FORM ...
Page 35
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...