PIC18F86K90-I/PT Microchip Technology, PIC18F86K90-I/PT Datasheet - Page 304

• Manufacturer Part Number: PIC18F86K90-I/PT
• Description: 64kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TRA
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F86K90-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87K90 FAMILY
21.3.2
When initializing the SPI, several options need to be
specified. This is done by programming the appropriate
control bits (SSPxCON1<5:0> and SSPxSTAT<7:6>).
These control bits allow the following to be specified:
• Master mode (SCKx is the clock output)
• Slave mode (SCKx is the clock input)
• Clock Polarity (Idle state of SCKx)
• Data Input Sample Phase (middle or end of data
• Clock Edge (output data on rising/falling edge of
• Clock Rate (Master mode only)
• Slave Select mode (Slave mode only)
Each MSSP module consists of a transmit/receive shift
register (SSPxSR) and a buffer register (SSPxBUF).
The SSPxSR shifts the data in and out of the device,
MSb first. The SSPxBUF holds the data that was written
to the SSPxSR until the received data is ready. Once the
8 bits of data have been received, that byte is moved to
the SSPxBUF register. Then, the Buffer Full detect bit,
BF (SSPxSTAT<0>), and the interrupt flag bit, SSPxIF,
are set. This double-buffering of the received data
(SSPxBUF) allows the next byte to start reception before
reading the data that was just received. Any write to the
SSPxBUF register during transmission/reception of data
will be ignored and the Write Collision Detect bit, WCOL
(SSPxCON1<7>), will be set. User software must clear
the WCOL bit so that it can be determined if the
following write(s) to the SSPxBUF register completed
successfully.
EXAMPLE 21-1:
DS39957B-page 304
LOOP
output time)
SCKx)
BTFSS
BRA
MOVF
MOVWF
MOVF
MOVWF
OPERATION
SSP1STAT, BF
LOOP
SSP1BUF, W
RXDATA
TXDATA, W
SSP1BUF
LOADING THE SSP1BUF (SSP1SR) REGISTER
;Has data been received (transmit complete)?
;No
;WREG reg = contents of SSP1BUF
;Save in user RAM, if data is meaningful
;W reg = contents of TXDATA
;New data to xmit
Preliminary
When the application software is expecting to receive
valid data, the SSPxBUF should be read before the next
byte of data to transfer is written to the SSPxBUF. The
Buffer Full bit, BF (SSPxSTAT<0>), indicates when
SSPxBUF has been loaded with the received data
(transmission is complete). When the SSPxBUF is read,
the BF bit is cleared. This data may be irrelevant if the
SPI is only a transmitter. Generally, the MSSP interrupt
is used to determine when the transmission/reception
has completed. If the interrupt method is not going to be
used, then software polling can be done to ensure that a
write collision does not occur. Example 21-1 shows the
loading
transmission.
The SSPxSR is not directly readable or writable and
can only be accessed by addressing the SSPxBUF
register. Additionally, the SSPxSTAT register indicates
the various status conditions.
21.3.3
The drivers for the SDOx output and SCKx clock pins
can be optionally configured as open-drain outputs.
This feature allows the voltage level on the pin to be
pulled to a higher level through an external pull-up
resistor, and allows the output to communicate with
external circuits without the need for additional level
shifters. For more information, see Section 11.1.3
“Open-Drain Outputs”.
The open-drain output option is controlled by the
SSP2OD
(ODCON1<7>). Setting an SSPxOD bit configures the
SDOx and SCKx pins for the corresponding module for
open-drain operation.
Note:
of
OPEN-DRAIN OUTPUT OPTION
To avoid lost data in Master mode, a
read of the SSPxBUF must be per-
formed to clear the Buffer Full (BF)
detect bit (SSPxSTAT<0>) between
each transmission.
(ODCON1<0>)
the
SSPxBUF
 2010 Microchip Technology Inc.
and
(SSPxSR)
SSP1OD
for
data
bits