MCP4021-202E/SN Microchip Technology, MCP4021-202E/SN Datasheet - Page 5

• Manufacturer Part Number: MCP4021-202E/SN
• Description: IC DGTL POT 2.1K 1CH 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP4021-202E/SN

• Memory Type: Non-Volatile
• Taps: 64
• Resistance (ohms): 2.1K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Interface: Up/Down
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 2.10K
• End To End Resistance: 2.1kohm
• Resistance Tolerance: ± 20%
• No. Of Steps: 64
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: Serial
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP4XXXDM-DB - BOARD DAUGHTER DIGIPOT MCP4XXXMCP402XEV - BOARD EVAL FOR MCP402X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AC/DC CHARACTERISTICS (CONTINUED)
© 2006 Microchip Technology Inc.
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
T
T
Digital Inputs/Outputs (CS, U/D)
Input High Voltage
Input Low Voltage
High-Voltage Input Entry Voltage
High-Voltage Input Exit Voltage
CS Pull-up/Pull-down Resistance
CS Weak Pull-up/Pull-down Current
Input Leakage Current
CS and U/D Pin Capacitance
RAM (Wiper) Value
Value Range
EEPROM
Endurance
EEPROM Range
Initial Factory Setting
Power Requirements
Power Supply Sensitivity
(MCP4021 and MCP4023 only)
Note 1:
A
A
= -40°C to +125°C, 2.1 kΩ, 5 kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for V
= +25°C.
2:
3:
4:
5:
6:
7:
8:
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP4021/23 only, test conditions are: I
MCP4022/24 only, test conditions are:
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design
Non-linearity is affected by wiper resistance (R
Section 6.0 “Resistor” for additional information.
The MCP4021 is externally connected to match the configurations of the MCP4022 and MCP4024, and then tested.
Parameters
Resistance
Device
2.1 kΩ
10 kΩ
50 kΩ
5 kΩ
2.25 mA
1.4 mA
450 µA
90 µA
5.5V
Current at Voltage
C
E
IN
ndurance
Sym
V
V
PSS
R
V
I
, C
V
I
PU
IHH
IHH
N
N
N
CS
IL
W
IH
IL
1.1 mA
450 µA
210 µA
40 µA
OUT
2.7V
with V
W
0.7 V
A
= 1.9 mA, code = 00h.
Min
8.5
0h
0h
= V
—
—
—
—
-1
—
—
—
—
DD
DD
MCP4022 includes V
MCP4024 includes V
W
), which changes significantly over voltage and temperature. See
and V
0.0015
0.0015
Typ
170
1M
—
—
—
—
16
—
10
—
—
1Fh
B
= V
Comments
SS
V
0.3 V
DD
0.0035
0.0035
12.5
. (-202 devices V
Max
3Fh
3Fh
+0.8
—
—
—
—
—
1
(6)
DD
WZSE
WFSE
(6)
Cycles
Units
%/%
%/%
hex
hex
hex
MCP4021/2/3/4
kΩ
µA
µA
pF
V
V
V
V
A
= 4V).
Threshold for WiperLock™
Technology
V
V
V
f
WiperLock Technology = Off
V
Code = 1Fh
V
Code = 1Fh
C
DD
DD
IN
DD
DD
= 1 MHz
= V
= 5.5V, V
= 5.5V, V
= 4.5V to 5.5V, V
= 2.7V to 4.5V, V
DD
DD
Conditions
CS
CS
= 5.5V, V
DS21945E-page 5
= 3V
= 3V
A
A
SS
= 4.5V,
= 2.7V,
= 0V,