AD73360AR-REEL7 Analog Devices Inc, AD73360AR-REEL7 Datasheet - Page 17

• Manufacturer Part Number: AD73360AR-REEL7
• Description: IC ANALOG FRONT END 6CH 28-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD73360AR-REEL7

• Number Of Channels: 6
• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Power (watts): 80mW
• Voltage - Supply, Analog: 3V
• Voltage - Supply, Digital: 3V
• Package / Case: 28-SOIC (7.5mm Width)
• Analog Front End Type: General Purpose
• Analog Front End Category: General Purpose
• Interface Type: Serial (6-Wire)
• Sample Rate: 64KSPS
• Input Voltage Range: 1.64375V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Resolution: 16b
• Number Of Adc's: 6
• Power Supply Type: Analog/Digital
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SOIC W
• For Use With: EVAL-AD73360LEB - BOARD EVAL FOR AD73360L
• Lead Free Status / RoHS Status: Not Compliant

CONTROL REGISTER G
CONTROL REGISTER H
REGISTER BIT DESCRIPTIONS
Control Register A
CRA:0
CRA:1
CRA:2
CRA:3
CRA:4–6
CRA:7
Control Register B
CRB:0–1
CRB:2–3
CRB:4–6
CRB:7
REV. A
Data/Program Mode. This bit controls the operating mode of the AD73360. If CRA:1 is 0, then a 0 in this bit
places the part in Program Mode. If CRA:1 is 0, then a 1 in this bit places the part in Data Mode.
Mixed Mode. If this bit is a 0, then the operating mode is determined by CRA:0. If this bit is a 1, then the
part operates in Mixed Mode.
Reserved. This bit is reserved and should be programmed to 0 to ensure correct operation.
SPORT Loop Back. This is a diagnostic mode. This bit should be set to 0 to ensure correct operation.
Device Count Bits. These bits tell the AD73360 how many devices are used in a cascade. All devices in the
cascade should be programmed to the same value ensure correct operation. See Table XVIII.
Reset. Writing a 1 to this bit will initiate a software reset of the AD73360.
Decimation Rate. These bits are used to set the decimation of the AD73360. See Table VII.
Serial Clock Divider. These bits are used to set the serial clock frequency. See Table VI.
Master Clock Divider. These bits are used to set the Master Clock Divider ratio. See Table V.
Control Echo Enable. Setting this bit to a 1 will cause the AD73360 to write out any control words it receives.
This is used as a diagnostic mode. This bit should be set to 0 for correct operation in Mixed Mode or Data Mode.
Bit Name
0
1
2
3
4
5
6
7
Bit Name
0
1
2
3
4
5
6
7
SEEN
INV
7
7
CH1
CH2
CH3
CH4
CH5
CH6
RMOD
SEEN
CH1
CH2
CH3
CH4
CH5
CH6
TME
INV
Table XIII. Control Register G Description
Table XIV. Control Register H Description
RMOD
TME
6
6
Description
Channel 1 Select
Channel 2 Select
Channel 3 Select
Channel 4 Select
Channel 5 Select
Channel 6 Select
Reset Analog Modulator
Enable Single-Ended Input Mode
Description
Channel 1 Select
Channel 2 Select
Channel 3 Select
Channel 4 Select
Channel 5 Select
Channel 6 Select
Test Mode Enable
Enable Invert Channel Mode
CH6
CH6
5
5
–17–
CH5
CH5
4
4
CH4
CH4
3
3
CH3
CH3
2
2
CH2
CH2
1
1
CH1
CH1
0
0
AD73360