5962-9098903MLA E2V, 5962-9098903MLA Datasheet - Page 3

• Manufacturer Part Number: 5962-9098903MLA
• Manufacturer: E2V

Specifications of 5962-9098903MLA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
(Copies of these documents are available online at
Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation.
(Applications for copies of ASTM publications should be addressed to: ASTM International, PO Box C700, 100 Barr Harbor
Drive, West Conshohocken, PA 19428-2959; http://www.astm.org.)
_______
3/
maximum levels may degrade performance and affect reliability.
4/ Must withstand the added P
1.3 Absolute maximum ratings. 3/
1.4 Recommended operating conditions.
2. APPLICABLE DOCUMENTS
2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein.
AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
Supply voltage to ground potential ............................................-0.5 V dc to +7.0 V dc
DC voltage range applied to outputs in high-Z state ..................-0.5 V dc to +7.0 V dc
DC input voltage .......................................................................-3.0 V dc to +7.0 V dc
Maximum power dissipation (P
Lead temperature (soldering, 10 seconds).................................+260°C
Thermal resistance, junction-to-case (θ
Junction temperature (T
Storage temperature range ........................................................-65°C to +150°C
Output current into outputs (low) ................................................-16 mA
Data retention ............................................................................10 years (minimum)
Endurance..................................................................................25 erase/write cycles (minimum)
Supply voltage (V
Ground voltage (GND) ...............................................................0 V dc
Input high voltage (V
Input low voltage (V
DEPARTMENT OF DEFENSE SPECIFICATION
DEPARTMENT OF DEFENSE STANDARDS
DEPARTMENT OF DEFENSE HANDBOOKS
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
Temperature under bias ............................................................-55°C to +125°C
Case operating temperature range (T
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
MIL-STD-883
MIL-STD-1835 -
MIL-HDBK-103 -
MIL-HDBK-780 -
ASTM Standard F1192-00
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
CC
STANDARD
-
) ..................................................................+4.5 V dc to +5.5 V dc
IL
IH
) ................................................................0.8 V dc maximum
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
)...............................................................2.2 V dc minimum
J
)...........................................................+175°C
D
due to short circuit test; e.g., I
D
) 4/ ..........................................1.0 W
C
) .....................................-55°C to +125°C
Standard Guide for the Measurement of Single Event Phenomena (SEP)
JC
Induced by Heavy Ion Irradiation of Semiconductor Devices
) .................................See MIL-STD-1835
http://assist.daps.dla.mil/quicksearch/
OS
.
SIZE
A
REVISION LEVEL
or
http://assist.daps.dla.mil
A
SHEET
5962-90989
or from the
3