5962-9098903MLA E2V, 5962-9098903MLA Datasheet - Page 15

• Manufacturer Part Number: 5962-9098903MLA
• Manufacturer: E2V

Specifications of 5962-9098903MLA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
Delta limits shall apply to group C inspection and shall consist of tests specified in table IIB herein.
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
4.4.1 Group A inspection.
a.
b.
c.
a.
b.
c.
e. O/V (latch-up) tests shall be measured only for initial qualification and after any design or process changes which may
f.
d. For device class M, subgroups 7, 8A, and 8B tests shall be sufficient to verify the truth table. For device classes Q and V,
DEFENSE SUPPLY CENTER COLUMBUS
affect the performance of the device. For device class M, procedures and circuits shall be maintained under document
revision level control by the manufacturer and shall be made available to the preparing activity or acquiring activity upon
request. For device classes Q and V, the procedures and circuits shall be under the control of the device
manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the preparing activity or
acquiring activity upon request. Testing shall be on all pins, on five devices with zero failures. Latch-up test shall be
considered destructive. Information contained in JEDEC Standard EIA/JESD 78 may be used for reference.
Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-
STD-883.
T
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
subgroups 7 and 8 shall include verifying the functionality of the device.
Tests shall be as specified in table IIA herein.
Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
Subgroup 4 (C
design changes which may affect input or output capacitance. Capacitance shall be measured between the designated
terminal and GND at a frequency of 1 MHz. Sample size is 15 devices with no failures, and all input and output
terminals tested.
Devices shall be tested for programmability and ac performance compliance to the requirements of group A, subgroups
9, 10, and 11. Either of two techniques is acceptable:
(2)
A
(1) Testing all devices submitted for test using additional built-in test circuitry which allows the manufacturer to verify
= +125°C, minimum.
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
programmability and ac performance without programming the user array. If this is done, the resulting test
patterns shall be verified on all devices during subgroups 9, 10, and 11, group A testing in accordance with the
sampling plan specified in MIL-STD-883, method 5005.
If such compliance cannot be tested on an unprogrammed device, a sample shall be selected to satisfy
programmability requirements prior to performing subgroups 9, 10, and 11. Twelve devices shall be submitted to
programming (see 3.2.3.1). If any device fails to program, the lot shall be rejected. At the manufacturers option, the
sample may be increased to 24 total devices with no more than one total device failure allowable. Ten devices from
the programmability sample shall be submitted to the requirements of group A, subgroups 9, 10, and 11. If any
device fails, the lot shall be rejected. At the manufacturers option, the sample may be increased to 20 total devices
with no more than one total device failure allowable. After completion of all testing, the devices shall be erased and
verified except devices submitted to groups C and D testing.
STANDARD
IN
and C
OUT
measurements) shall be measured only for initial qualification and after any process or
SIZE
A
REVISION LEVEL
A
SHEET
5962-90989
15