HSDL-3220-021 Lite-On Electronics, HSDL-3220-021 Datasheet - Page 2

Infrared Transceivers IR Transceiver

HSDL-3220-021

Manufacturer Part Number
HSDL-3220-021
Description
Infrared Transceivers IR Transceiver
Manufacturer
Lite-On Electronics
Datasheet

Specifications of HSDL-3220-021

Wavelength
875 nm, 880 nm
Continual Data Transmission
4 Mbit/s
Transmission Distance
50 cm
Radiant Intensity
45 mW/sr
Half Intensity Angle Degrees
30 deg to 60 deg
Pulse Width
4 us, 1.6 us
Maximum Rise Time
60 ns, 600 ns
Maximum Fall Time
60 ns, 600 ns
Led Supply Voltage
0 V to 6.5 V
Maximum Forward Current
50 mA
Operating Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
- 25 C
Dimensions
8 mm x 3 mm x 2.5 mm
Data Rate
4Mbs (FIR)
Idle Current, Typ @ 25° C
1.8 mA
Link Range, Low Power
1m
Operating Temperature
-25°C ~ 70°C
Orientation
Side View
Shutdown
*
Size
8mm x 3mm x 2.5mm
Standards
IrPHY 1.4
Supply Voltage
2.7 V ~ 3.6 V
Lead Free Status / RoHS Status
Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Compliant
Application Support Information
The Application Engineering Group is available to as-
sist you with the application design associated with the
HSDL-3220 infrared transceiver module. You can con-
tact them through your local sales representatives for
additional details.
Order Information
Part Number
HSDL-3220-021
I/O Pins Configuration Table
Pin
1
2
3
4
5
6
7
8
-
Recommended Application Circuit Components
Component
R1
CX1, CX4
CX2, CX3
Notes:
1. Tied through external series resistor, R1, to regulated Vled from 2.7 to 5.5V. Please refer to table above for recommended series resistor value.
2. Internally connected to LED driver. Leave this pin unconnected.
3. This pin is used to transmit serial data when SD pin is low. If this pin is held high for longer than 50 µs, the LED is turned off. Do NOT float this
4. This pin is capable of driving a standard CMOS or TTL load. No external pull-up or pull-down resistor is required. The pin is in tri-state when
5. The transceiver is in shutdown mode if this pin is high for more than 400 µs. On falling edge of this signal, the state of the TXD pin sampled
6. Regulated, 2.7 to 3.6 Volts.
7. Connect to ASIC logic controller Vcc voltage or supply voltage. The voltage at this pin must be equal to or less than supply voltage.
8. Connect to system ground.
9. Connect to system ground via a low inductance trace. For best performance, do not connect directly to the transceiver pin GND.
10. CX1 must be placed within 0.7 cm of the HSDL-3220 to obtain optimum noise immunity.
11. In environments with noisy power supplies, including CX2, as shown in Figure 1, can enhance supply ripple rejection performance.
2
pin.
the transceiver is in shutdown mode. The receiver output echoes transmitted signal.
and used to set receiver low bandwidth (TXD=low) or high bandwidth (TXD=high) mode. Refer to the section ”Bandwidth selection timing”
for programming information. Do NOT float this pin.
Recommended Value
5.6Ω ± 5%, 0.25 watt for 2.7 ≤ Vled< 3.3V
10Ω ± 5%, 0.25 watt for 3.3 ≤ Vled<4.2V
15Ω ± 5%, 0.25 watt for 4.2 ≤Vled< 5.5V
0.47 µF ± 20%, X7R Ceramic
6.8 µF ± 20%, Tantalum
Symbol
LED A
LED C
TXD
RXD
SD
Vcc
IOVcc
GND
Shield
Packaging Type
Tape and Reel
Description
LED Anode
LED Cathode
Transmit Data. Active High.
Receive Data. Active Low.
Shutdown. Active High.
Supply Voltage
Input/Output ASIC Vcc
Ground
EMI Shield
Marking Information
The unit is marked with ‘yyww’ on the shield:
Package
Front View
yy = year
ww = work week
Notes
10
11
Quantity
I/O Type
O
I
I
I
2500
Notes
1
2
3
4
5
6
7
8
9

Related parts for HSDL-3220-021