CPC5602C Clare, CPC5602C Datasheet - Page 14

• Manufacturer Part Number: CPC5602C
• Description: MOSFET N-CH 350V 5MA SOT-223
• Manufacturer: Clare

Specifications of CPC5602C

• Fet Type: MOSFET N-Channel, Metal Oxide
• Fet Feature: Depletion Mode
• Rds On (max) @ Id, Vgs: 14 Ohm @ 50mA, 350mV
• Drain To Source Voltage (vdss): 350V
• Current - Continuous Drain (id) @ 25° C: 5mA
• Input Capacitance (ciss) @ Vds: 300pF @ 0V
• Power - Max: 2.5W
• Mounting Type: Surface Mount
• Package / Case: SOT-223 (3 leads + Tab), SC-73, TO-261
• Transistor Polarity: N-Channel
• Resistance Drain-source Rds (on): 14 Ohms
• Continuous Drain Current: 5 mA
• Power Dissipation: 2.5 W
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Gate Charge (qg) @ Vgs: -
• Vgs(th) (max) @ Id: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

CPC2400E
14
Modem S-Registers
The value of an S-register is modified by ATSn =x,
where n is the register number and x is the value to be
stored in that particular register. Each S-register has
S20
Register
S0
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
Range
0 - 255
0 - 255
0 - 255
0 - 127
0 - 127
0 - 127
2 - 255
1 - 255
0 - 255
1 - 255
1 - 255
50 - 255
0 - 255
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
-6 to -43 -
Units
Rings
Rings
ASCII
ASCII
ASCII
ASCII
Seconds
Seconds
Seconds
1/10th sec
1/10th sec
msec
1/50th sec
Reserved
Reserved
Reserved
Reserved
dBm
Reserved
Reserved
Reserved
Reserved
Delay to Wait when a Comma Dial Modifier is Processed. Default = 2 sec.
Time Carrier Must be Present Before Being Recognized. Default = 0.6 sec.
Delay Between Lost Carrier and Hang Up. Setting S-register S10 to 255 makes the
Escape Prompt delay time. This is the prompt delay time for escape sequences
Description
Set number of rings to auto-answer. The country configuration may disable the
modem’s ability to detect a telephone line ring signal. In this case the modem will
never automatically answer the telephone regardless of the S0 setting. Default = 0
(auto-answer disabled)
Returns the number of times the phone rings. Default = 0
Set Escape Sequence Character. Setting S2 to a value greater than 127 disables the
character escape sequence, preventing the modem from returning to Command
state when in the On-Line state. Default = 43
Set the End of Line character. Default = 13
Set the Line Feed Character. Default = 10
Set the BackSpace Character. Default = 8
Delay to Wait Before Performing a Blind Dial. Default = 2 seconds
Delay to Wait for Carrier after dialing. Default = 30 seconds
modem never hang up the telephone line because of a loss of carrier. Default = 14
tenths of a second
Multi-Frequency Tone duration. Default = 95 milliseconds
from the On-Line state to the Command state. Default = 50 fiftieths of a second
Reserved
Reserved
Reserved
Reserved
Set Transmit level. Default = -10 dBm
Reserved
Reserved
www.clare.com
three values that may be configured for different coun-
tries: a default value, an upper limit and a lower limit.
The values shown in this manual are for North America.
Rev. 2